Device Overview

ManufacturerPopp & Co
Manufacturer ID0154
NamePOPE701202
Device DescriptionPopp Mold detector
CategorySensor
References (Type:Id)0004:0014
Firmware VersionsAll
Protocol Version6.002
Library TypeLIB_SLAVE_ENHANCED
Always ListeningNo
Frequently ListeningNo
Supports RoutingYes
Supports BeamingYes
Supports SecurityNo
Maximum Data Rate40000
Device Overview

Product Description

This device measures the three air quality parameters temperature, humidity and dew point an reports them to a central controller. Beside this, the device can directly control groups of other Z-Wave devices on over- and undershooting a set temperature and/or humidity parameter. This can be used to establish control loops for temperature and humidity. The device wakes up every 4 minutes to measure the values and it will send unsolicited reports when values change. Additionally, the device will report all values on request.
The mold detector is actively monitoring the danger of mold in a room based on the temperature and humidity and will issue alarm warnings when critical air conditions met. Wireless Alarm and red and a green blinking LED will indicate a mold condition. This local LED warning function is also available when the device is not included in any Z-Wave network and works stand alone.

The POPP Mold Detector can be mounted in two ways.

  1. use the enclosed adhesive tape. Clean the substrate carefully from grease and dirt to achieve optimum strength of the adhesive areas.
  2. use the enclosed screws and dowels to fix it to the wall or other surface.
Inclusion Information

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Tripple clicking the tamper button includes (adds) the device.

Exclusion Information

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Tripple clicking the tamper button excludes (removes) the device.

Wakeup Information

Communication to a Sleeping device (Wakeup)

This device is battery operated and turned into deep sleep state most of the time to save battery life time. Communication with the device is limited. In order to communicate with the device, a static controller C is needed in the network. This controller will maintain a mailbox for the battery operated devices and store commands that can not be received during deep sleep state. Without such a controller, communication may become impossible and/or the battery life time is significantly decreased.

This device will wakeup regularly and announce the wakeup state by sending out a so called Wakeup Notification. The controller can then empty the mailbox. Therefore, the device needs to be configured with the desired wakeup interval and the node ID of the controller. If the device was included by a static controller this controller will usually perform all necessary configurations. The wakeup interval is a tradeoff between maximal battery life time and the desired responses of the device. To wakeup the device please perform the following action: A single click on the tamper button will wakeup the device.

Usage Information

Open the  POPP Mold Detector
To open the POPP Mold Detector, press the lock with your finger and pull the housing cover upwards.

Tamper button
The tamper button is located on the side of the POPP Mold Detector. This button is also used for inclusion and exclusion.

Functionality 
Once the device is powered up it will start monitoring the air parameters and warn of mold using the local red and green LED. All air parameters are measured every 4 minutes. Pushing the button will force an immediate measurement and the LEDs will indicate the danger of mold

  • green: no danger of mold in the room
  • red: danger of mold, on the windows to lower the humidity

The device contains three sensors with the following accuracy measures:

  • Humidity: +/- 3 % on relative humidity, +/-1 % hysteresis
  • Temperature: 0 ... 65 °C +/- 1 Kelvin
  • Dew Point: 0 ... 65 °C +/- 1 Kelvin (calculated from other sensor values)

Besides the measured values the device will issue Z-Wave notifications on moisture (0x10).

Node Information Frame
The Node Information Frame (NIF) is the business card of a Z-Wave device. It contains information about the device type and the technical capabilities. The inclusion and exclusion of the device is confirmed by sending out a Node Information Frame. Beside this it may be needed for certain network operations to send out a Node Information Frame. To issue a NIF execute the following action: Tripple Click the tamper button

Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SENSOR_NOTIFICATION
Specific ClassSPECIFIC_TYPE_NOTIFICATION_SENSOR
Unique Referencepope701202

Configuration Parameters

Parameter 1
Bitmask
LabelMin. Temp. change
DescriptionMinimum Temperature change to report
Word Size1
Default Value20
Allowable Range0 to 100
Overview


This value defines the minimum change of temperature to cause an unsolicited report of humidity to the central controller using Lifeline.
If the value is set to 0, there will be no reports sent to the controller, when the temperature changes. However, periodic reports, managed by configuration parameter 4, may still be active.
Size: 1 Byte, Default Value: 20

1-100: 1/10 degree
0: disabled

Options
Option Value0
Option Labeldisabled
Option Overview

If the value is set to 0, there will be no reports sent to the controller, when the temperature changes. However, periodic reports, managed by configuration parameter 4, may still be active.

Parameter 2
Bitmask
LabelMin humidity change.
DescriptionMinimum humidity change to report
Word Size1
Default Value7
Allowable Range0 to 20
Overview

Parameter 2: Minimum humidity change to report

This value defines the minimum change of humidity to cause an unsolicited report of humidity to the central controller using Lifeline.
If the value is set to 0, there will be no reports sent to the controller, when the humidity changes. However, periodic reports, managed by configuration parameter 4, may still be active.
Size: 1 Byte, Default Value: 7

Options
Option Value0
Option Labeldisabled
Option Overview

If the value is set to 0, there will be no reports sent to the controller, when the humidity changes. However, periodic reports, managed by configuration parameter 4, may still be active. 

Parameter 4
Bitmask
LabelPeriodic Reports
DescriptionPeriodic Reports
Word Size2
Default Value43200
Allowable Range0 to 65535
Overview

Parameter 4: Periodic Reports

This parameter defines the time interval to send an unsolicited report.
If the value is set to 0, there will be no periodic reports sent to the controller. However, reports on temperature/humidity changes, managed by configuration parameters 1 and 2, may still be active.
Size: 2 Byte, Default Value: 43200

Options
Option Value0
Option Labeldisabled
Option Overview

If the value is set to 0, there will be no periodic reports sent to the controller. However, reports on temperature/humidity changes, managed by configuration parameters 1 and 2, may still be active

Parameter 5
Bitmask
LabelTemperature Upper Watermark
DescriptionTemperature Upper Watermark value
Word Size2
Default Value0
Allowable Range0 to 1000
Overview

Parameter 5: Temperature Upper Watermark value

This parameter defines a temperature. If the measured temperature surpasses this watermark a BASIC command is sent into Association Group 2
Size: 2 Byte, Default Value: 0

1-1000; 1/10 degree
0: disabled

Options
Option Value0
Option Labeldisabled
Option Overview
Parameter 6
Bitmask
LabelTemperature Lower Watermark
DescriptionTemperature Lower Watermark value
Word Size2
Default Value0
Allowable Range-200 to 1000
Overview

Parameter 6: Temperature Lower Watermark value

This parameter defines a temperature. If the measured temperature dropps below this watermark a BASIC command is sent into Association Group 3
Size: 2 Byte, Default Value:0

-200-1000: 1/10 degree
0: disabled

Options
Parameter 7
Bitmask
LabelHumidity Upper Watermark
DescriptionHumidity Upper Watermark value
Word Size1
Default Value0
Allowable Range10 to 100
Overview

Parameter 7: Humidity Upper Watermark value

This parameter defines a relative humidity. If the measured relative humidity surpasses this watermark a BASIC command is sent into Association Group 4
Size: 1 Byte, Default Value: 0

10-100: %
0: disabled

Options
Option Value0
Option Labeldisabled
Option Overview
Parameter 8
Bitmask
LabelHumidity Lower Watermark
DescriptionHumidity Lower Watermark value
Word Size1
Default Value0
Allowable Range0 to 90
Overview

Parameter 8: Humidity Lower Watermark value

This parameter defines a relative humidity. If the measured temperature dropps below this relative humidity a BASIC command is sent into Association Group 5
Size: 1 Byte

1-90: %
0: disabled

Options
Option Value0
Option Labeldisabled
Option Overview
Parameter 9
Bitmask
LabelLow Temperature Trigger
DescriptionLow Temperature Trigger BASIC Set Command Value
Word Size1
Default Value255
Allowable Range0 to 255
Overview

Parameter 9: Low Temperature Trigger BASIC Set Command Value

This defines what BASIC command shall be sent out into association group 3
Size: 1 Byte, Default Value: 255

Options
Parameter 10
Bitmask
LabelHigh Temperature Trigger
DescriptionHigh Temperature Trigger BASIC Set Command Value
Word Size1
Default Value0
Allowable Range0 to 255
Overview

Parameter 10: High Temperature Trigger BASIC Set Command Value

This defines what BASIC command shall be sent out into association group 2
Size: 1 Byte, Default Value: 0

Options
Parameter 11
Bitmask
LabelLow Humidity Trigger
DescriptionLow Humidity Trigger BASIC Set Command Value
Word Size1
Default Value255
Allowable Range0 to 255
Overview

Parameter 11: Low Humidity Trigger BASIC Set Command Value

This defines what BASIC command shall be sent out into association group 5
Size: 1 Byte, Default Value: 255

Options
Parameter 12
Bitmask
LabelHigh Humidity Trigger
DescriptionHigh Humidity Trigger BASIC Set Command Value
Word Size1
Default Value0
Allowable Range0 to 255
Overview

Parameter 12: High Humidity Trigger BASIC Set Command Value

This defines what BASIC command shall be sent out into association group 4
Size: 1 Byte, Default Value: 0

Options

Association Groups

Group ID1
LabelLifeline
DescriptionLifeline
Maximum Nodes5
ControllerYes
Overview
Group ID2
LabelTemperature High Trigger
DescriptionTemperature High Trigger
Maximum Nodes5
ControllerYes
Overview
Group ID3
LabelTemperature Low Trigger
DescriptionTemperature Low Trigger
Maximum Nodes5
ControllerYes
Overview
Group ID4
LabelHumidity High Trigger
DescriptionHumidity High Trigger
Maximum Nodes5
ControllerYes
Overview
Group ID5
LabelHumidity Low Trigger
DescriptionHumidity Low Trigger
Maximum Nodes5
ControllerYes
Overview

Endpoints

Endpoint NameEndpoint 0
Endpoint Number0
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SENSOR_NOTIFICATION
Specific ClassSPECIFIC_TYPE_NOTIFICATION_SENSOR
Command Classes
Class Ver Basic NIF Sec UnSec
NO_OPERATION 1
BASIC 1
SENSOR_BINARY 2
Binary Sensor
SENSOR_MULTILEVEL 8
Sensor (dew point)
Sensor (temperature)
Sensor (relative humidity)
ASSOCIATION_GROUP_INFO 1
DEVICE_RESET_LOCALLY 1
ZWAVE_PLUS_INFO 1
CONFIGURATION 1
ALARM 8
Alarm
MANUFACTURER_SPECIFIC 1
POWERLEVEL 1
FIRMWARE_UPDATE_MD 1
BATTERY 1
WAKE_UP 2
ASSOCIATION 2
VERSION 2
MULTI_INSTANCE_ASSOCIATION 3
Endpoint NameEndpoint 0
Endpoint Number0
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SENSOR_NOTIFICATION
Specific ClassSPECIFIC_TYPE_NOTIFICATION_SENSOR
Command Classes
Class Ver Basic NIF Sec UnSec

Reference Documents

Popp Mold detector SKU: POPE701202 POPE701202.pdf
Popp Mold detector SKU: POPE701202 Mold-Detector.jpg

First added to database on -0001-11-30 00:00:00. Current released version is 2.
Last updated by sihui on 2019-12-04 20:21:46 (2 months ago).
Approved on 2019-12-04 20:22:02, and last exported on 2019-12-25 16:56:48.

You have no rights to post comments