• Endpoint 0 contains both switch and dimmer channels. It probably should only include dimmer!

Device Overview

ManufacturerAEON Labs
Manufacturer ID0086
NameZW141
Device DescriptionNano Shutter Controller
CategoryBlinds
References (Type:Id)0003:008D,0103:008D
Firmware VersionsAll
Protocol Version5.003
Library TypeLIB_SLAVE_ENHANCED
Always ListeningYes
Frequently ListeningNo
Supports RoutingYes
Supports BeamingYes
Supports SecurityNo
Maximum Data Rate40000
Device Overview

Aeotec Nano Shutter is a Z-Wave motor controller specifically used to enable Z-Wave command and control (up/down/stop) for existing window covering motors.

It can connect to 2 external manual switches/buttons to control the motor up/down/stop independently. Its surface has a pin socket, which can be used for connecting to the touch panel, so you can also use the touch panel to control the Nano Shutter.

The wireless module is powered from the mains supply. In the event of power failure, non-volatile memory retains all programmed information relating to the units operating status.

Nano Shutter is also a security Z-Wave plus device and supports Over The Air (OTA) feature for the products firmware upgrade.

It can be a repeater in the Z-Wave network. Acting as a bridge for communication, it will forward Z-Wave command messages to their destinations if the originating controller is out of range from the destination node. 

Inclusion Information
  1. Set your Z-Wave controller into pairing mode.
  2. Press the Action Button on the Nano Dimmer or toggle the external manual switch once, the green LED (non-secure indication) will blink to indicate the Nano Dimmer is entering into pairing mode.
  3. If the Nano Dimmer has been successfully added to your Z-Wave network, its RGB LED will be solid. If the pairing was unsuccessful, the red LED will be on for 2 seconds and then remain a colourful gradient, repeat the instructions above from step 1.
Exclusion Information
  1. Set your Z-Wave controller into removal mode.
  2. Press the Action Button 6 times on the Nano Dimmer or toggle the external manual switch 2 times in fast succession.
  3. If the Nano Dimmer has been successfully removed from your Z-Wave network, its RGB LED will remain colourful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load), repeat the instructions above from step 1.
Usage Information

Controlling the Nano Shutter.

  • Use any of the below methods to control the Nano Shutter.
  • Pressing the button on the external (Wall) switch will be able to spin the motor up/down/stop through the usage of Z-Wave commands built into Z-Wave certified controllers and gateways (The specific Z-Wave commands supporting this function are the Basic Command Class and Multilevel Switch Command Class.) Please consult the operation manual for these controllers for specific instructions on controlling the Motor Controller.
  • A short press on the button on the Motor Controller will spin the motor up/down/stop.
  • Change Mode on the External Switch/Button Control.
  • Nano Shutter by default is set to be controlled via 2-state (flip/flop) external wall switch.
  • Pushing the button 6 times in quick succession on the Nano Shutter will swap between this default mode and the momentary push button external wall switch mode

Reset your Nano Shutter

  • If at some stage, your primary controller is missing or inoperable, you may wish to reset all of your Nano Shutter’s settings to their factory defaults. To do this, press and hold the Action Button for 20 seconds and then release it. Your Nano Shutter will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colourful gradient status as a confirmation.
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_MULTILEVEL
Specific ClassSPECIFIC_TYPE_CLASS_A_MOTOR_CONTROL
Unique Referencezw141

Configuration Parameters

Parameter 35
Bitmask
LabelMoving time left to right
DescriptionSet the moving time from up (left) to down (right) for curtain.
Word Size1
Default Value30
Allowable Range0 to 100
Overview
Options
Parameter 80
Bitmask
LabelReport sent to nodes in association group 1
DescriptionReport sent to associated nodes in association group 1
Word Size1
Default Value0
Allowable Range0 to 1
Overview

To set which report would be sent to the associated nodes in association group 1 when the state of output load is changed.
0 = Nothing
1 = Basic Report CC
Note: When just only one channel load state is changed, the report message Basic Report CC would be Multi Channel encapsulated.

Options
Parameter 85
Bitmask
LabelOperation mode of external switch
DescriptionOperation mode of external switch
Word Size1
Default Value0
Allowable Range0 to 1
Overview

Set the operation mode of external switch.
0 = Operation Mode 1.
1 = Operation Mode 2.
For detailed instructions for Operation Mode 1 and 2, see end of this table.

Options
Parameter 120
Bitmask
LabelExternal switch mode of S1
DescriptionExternal switch mode of S1
Word Size1
Default Value0
Allowable Range0 to 4
Overview

Set the external switch mode of S1
0 = Unidentified mode.
1 = Reserved.
2 = 3 way switch mode
3 = Push button mode
4 = Enter automatic identification mode (The blue Led will fast blink).
Note: When the switch mode of S1 is determined or identified or configured, this mode value will not be reset after exclusion.

Options
Parameter 121
Bitmask
LabelExternal switch mode of S2
DescriptionExternal switch mode of S2
Word Size1
Default Value0
Allowable Range0 to 4
Overview

Set the external switch mode of S2
0 = Unidentified mode.
1 = Reserved
2 = 3 way switch mode
3 = push button mode
4 = enter automatic identification mode (The green Led will fast blink).
Note: When the switch mode of S2 is determined or identified or configured, this mode value will not be reset after exclusion.

Options
Parameter 252
Bitmask
LabelEnable/disable config parameters to be locked
DescriptionEnable/disable the configuration parameters to be locked
Word Size1
Default Value0
Allowable Range0 to 1
Overview

Enable/disable the configuration parameters to be locked.
0 = disable.
1 = enable.

Options

Association Groups

Group ID1
LabelLifeline
Description
Maximum Nodes5
ControllerYes
Overview

When the state of Nano Shutter (turn on/off the load ) is changed:

  1. Set Configuration parameter 80 to 0: Send nothing (default). 
  2. Set Configuration parameter 80 to 1: Send the Basic Report.
Group ID2
LabelGroup 2
Description
Maximum Nodes5
ControllerNo
Overview

Forward the Basic Set, Binary set, Scene Activation Set to associated nodes in Group 2 when the Nano Shutter receives the Basic Set, Binary set, Scene Activation Set commands from main controller. (E.g. Send/forward Basic Set to control the other nodes in association Group 2)

Endpoints

Endpoint NameEndpoint 0
Endpoint Number0
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_MULTILEVEL
Specific ClassSPECIFIC_TYPE_CLASS_A_MOTOR_CONTROL
Command Classes
Class Ver Basic NIF Sec UnSec
NO_OPERATION 1
BASIC 1
SWITCH_BINARY 1
Switch [deprecated]
SWITCH_MULTILEVEL 3
Dimmer [deprecated]
Blinds Control
SCENE_ACTIVATION 1
Scene Number
SCENE_ACTUATOR_CONF 1
ASSOCIATION_GROUP_INFO 1
DEVICE_RESET_LOCALLY 1
ZWAVE_PLUS_INFO 1
CONFIGURATION 1
MANUFACTURER_SPECIFIC 1
POWERLEVEL 1
FIRMWARE_UPDATE_MD 1
ASSOCIATION 2
VERSION 2
SECURITY 1

Reference Documents

manual Aeon-Labs-Nano-Shutter--manual.pdf
photo z-wave-nano-shutter.png

First added to database on -0001-11-30 00:00:00. Current released version is 8.
Last updated by Super User on 2019-11-17 19:24:23 (4 days ago).
Approved on 2019-11-17 19:26:50, and last exported on 2019-11-17 19:26:51.

Add comment