Device Overview

ManufacturerAEON Labs
Manufacturer ID0086
NameZW098
Device DescriptionLED Bulb
CategoryLight Bulb
References (Type:Id)0003:0062,0103:0062,0203:0062
Firmware VersionsAll
Protocol Version4.005
Library TypeLIB_SLAVE_ENHANCED
Always ListeningYes
Frequently ListeningNo
Supports RoutingYes
Supports BeamingNo
Supports SecurityYes
Maximum Data Rate
Device Overview

Aeon Labs LED Bulb is a switch multilevel device based on Z-wave enhanced 232 slave library of V6.51.06. Its bulb has the Smart RGB LEDs in, which can be used for adding colour to your home, the bulb has 5 main colour channels available for you to adjust: Red, Green, Blue, Warm white and Cold white. You can configure its indication colour according to your favour.

The LED Bulb can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

The LED Bulb is a security Z-Wave device, so a security enabled controller is needed for take full advantage of all functionally for the LED Bulb. It also supports the Over The Air (OTA) feature for the product’s firmware upgrade. 

Inclusion Information

Non-secure inclusion:

  1. Power on your LED Bulb.
  2. Set the primary controller into inclusion mode (If you don’t know how to do this, please refer to its manual).
  3. Turn off the LED Bulb and then turn on.
  4. If the inclusion is failed, please repeat the process from step 2. 

Secure inclusion:

  1. Power on your LED Bulb.
  2. Set the primary controller into inclusion mode (If you don’t know how to do this, please refer to its manual).
  3. Turn off the LED Bulb and then turn on it on 3 times within 2 seconds.
  4. If the inclusion fails, please repeat the process from step 2.

Note: If LED Bulb has been successfully included into your Z-Wave network, its warm white LED will be solid. If the linking was unsuccessful and the LED Bulb continues to be active with a colourful gradient. 

Exclusion Information
  1. Power on your LED Bulb.
  2. Set the primary controller into exclusion mode (If you don’t know how to do this, please refer to its manual).
  3. Turn off the LED Bulb and then turn on 3 times within 2 seconds.
  4. If the exclusion fails, please repeat the process from step 2.

Note: If LED Bulb has been successfully excluded from your Z-Wave network, its warm white LED will be active with a colourful gradient. If the exclusion was unsuccessful and the LED Bulb continues to be solid. 

Usage Information
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_MULTILEVEL
Specific ClassSPECIFIC_TYPE_POWER_SWITCH_MULTILEVEL
Unique Referencezw098

Configuration Parameters

Parameter 32
Bitmask
LabelToggle send report on color change
DescriptionToggle send report on color change
Word Size1
Default Value0
Allowable Range0 to 1
Overview

Enable/disable to send out a report when the color is changed.
0=disable.<default>
1=Hail CC.
Others=ignore.

Options
Option Value0
Option Labeldisable color updates
Option Overview
Option Value1
Option Labelsend HAIL CC
Option Overview
Parameter 34
Bitmask
LabelAllow external switch to toggle bulb
DescriptionAllow external switch to toggle bulb
Word Size1
Default Value0
Allowable Range0 to 1
Overview

Enable/disable the function of using External Switch to turn
on/off the bulb.
0=disable.
1=enable.
Others=ignore.

Options
Option Value0
Option Labeldisabled
Option Overview
Option Value1
Option Labelenabled
Option Overview
Parameter 35
Bitmask
LabelAllow external switch to change color
DescriptionAllow external switch to change color
Word Size1
Default Value1
Allowable Range0 to 1
Overview

Enable/disable the function of using External Switch to changes
the bulb’s color.
0=disable.
1=enable.
Others=ignore.

Options
Option Value0
Option Labeldisabled
Option Overview
Option Value1
Option Labelenabled
Option Overview
Parameter 36
Bitmask
LabelControl color mode
DescriptionReboot/save/exit Colorful mode
Word Size1
Default Value0
Allowable Range0 to 3
Overview

Reboot/save/exit Colorful mode.
0==Un-reboot Colorful mode.
1==Reboot Colorful mode.
2==Exit Colorful mode.
3==Save the current Colorful mode value and then exit

Options
Option Value0
Option Labelreboot normal mode
Option Overview
Option Value1
Option Labelboot into color programming
Option Overview
Option Value2
Option Labelexit color programming
Option Overview
Option Value3
Option Labelsave and exit color programming
Option Overview
Parameter 37
Bitmask000000FF
LabelColour Residence Time
DescriptionColour Residence Time
Word Size4
Default Value0
Allowable Range0 to 255
Overview

0-254 : Corresponds from 0 to 25.4 seconds.

255 : no change

Options
Parameter 37
Bitmask0000FF00
LabelColour Change Speed
DescriptionColour Change Speed
Word Size4
Default Value0
Allowable Range0 to 255
Overview

Colour Change Speed (8 bits)
This field specifies the transition speed when one colour changes to another.

 

0 is slowest adn 254 is fastest.  255 will have no effect.

Options
Parameter 37
Bitmask00FF0000
LabelCycle count
DescriptionCycle count
Word Size4
Default Value0
Allowable Range0 to 255
Overview


The Cycle Count is used to define the number of repetitions/cycles displayed by your LED Bulb in Colour
Display Cycle before stopping.

0 = Unlimited

1-254 = cycle this number and then stop

255 = no change to setting

 

For example:

When the Bulb is in Rainbow mode, the colour change from red to pink (Red Orange Yellow Green
Cyan Blue Purple Pink), going through the colours is regarded as 1 cycle.

Options
Parameter 37
Bitmask7F000000
LabelColor transitions (Value 1 MSB) see Overview
DescriptionValue 1 (MSB) see Overview
Word Size4
Default Value0
Allowable Range0 to 127
Overview

scroll to bottom for examples.

  • bits 7 and 6 for colour transition style
  • bits 5 and 4 are reserved (always 0)
  • bits 3,2,1,0 are colour display

colour display options are:

  • 0 single colour mode
  • 1 Rainbow Mode(red, orange, yellow, green, cyan, blue, violet,pinkish)
  • 2 Multi Colour Mode(colours cycle between selected colours)
  • 3 Random mode
  • 15 Inactive (keep current mode)

Single colour mode: The Bulb is solid with one colour in this mode. If you want to change its current
colour, you need to turn the Bulb off and on 2 times via wall switch within 1 second, the Bulb will enter
into colour change status. During this time, turning the wall switch off when your desired colour appears,
will be used as the colour of the bulb when it is on.

Rainbow mode: The Bulb has 8 colours to display and will change through a range of colors (Red
Orange Yellow Green Cyan Blue Violet pinkish).
Multi-colour mode: The Bulb can change between multiple colours according to the colour index which
is configurable through configuration parameter 38, see the configuration table of parameter 38 below.

Random mode: The Bulb’s colour will be displayed randomly.

Colour Transition Style (2 bits)

  • 0 Smooth transitions
  • 1 Fast/Direct transition
  • 2 Fade out/Fade in
  • 3 Inactive (keep current configuration)
Options
Option Value0
Option Labelsingle color mode, smooth color transitions
Option Overview

single color mode with smooth color transitions (default)

Option Value1
Option Labelrainbow mode with smooth color transitions
Option Overview
Option Value2
Option Labelmulti color mode with smooth color transitions
Option Overview
Option Value3
Option Labelrandom mode with smooth color transitions
Option Overview
Option Value64
Option Labelsingle color mode with direct color transitions
Option Overview
Option Value65
Option Labelrainbow color mode with direct color transitions
Option Overview
Option Value66
Option Labelmulti color mode with direct color transitions
Option Overview
Option Value67
Option Labelrandom color mode with direct color transitions
Option Overview
Option Value128
Option Labelsingle color mode, fade out/fade in
Option Overview

single color mode with fade out/fade in transitions

Option Value129
Option Labelrainbow color mode, fade out/fade in
Option Overview

rainbow color mode with fade out/fade in transitions

Option Value130
Option Labelmulti color mode, fade out/fade in
Option Overview

multi color mode with fade out/fade in transitions

Option Value131
Option Labelrandom color mode, fade out/fade in
Option Overview

random color mode with fade out/fade in transitions

Parameter 38
Bitmask000000FF
LabelColor index configuration for multi mode (1,2)
DescriptionColor index configuration for multi mode (1,2)
Word Size4
Default Value0
Allowable Range0 to 136
Overview

The colour will be changed from index 1 to index 8 circularly when your bulb is in Multi colour mode.

This value controls indexes 1 and 2

Values are additive.  The smaller numbers control index 1, and the larger control index 2. 

Example:

You want to have the 1st color be red and the 2nd color switched to to be blue.  Set this value to 97 (1+96)

 

The colors are:

1,16 = red

2,32 = orange

3,48 = yellow

4,64 = green

5,80 = cyan

6,96 = blue

7,112 = violet

8,128 = pinkish (Aeon's term)

Options
Parameter 38
Bitmask0000FF00
LabelColor index configuration for multi mode (3,4)
DescriptionColor index configuration for multi mode (3,4)
Word Size4
Default Value0
Allowable Range0 to 136
Overview

The colour will be changed from index 1 to index 8 circularly when your bulb is in Multi colour mode.

This value controls indexes 3 and 4

Values are additive.  The smaller numbers control index 3, and the larger control index 4. 

Example:

You want to have the 3rd color be red and the 4th color switched to to be blue.  Set this value to 97 (1+96)

 

The colors are:

1,16 = red

2,32 = orange

3,48 = yellow

4,64 = green

5,80 = cyan

6,96 = blue

7,112 = violet

8,128 = pinkish (Aeon's term)

Options
Parameter 38
Bitmask00FF0000
LabelColor index configuration for multi mode (5.6)
DescriptionColor index configuration for multi mode (5,6)
Word Size4
Default Value0
Allowable Range0 to 136
Overview

The colour will be changed from index 1 to index 8 circularly when your bulb is in Multi colour mode.

This value controls indexes 5 and 6

Values are additive.  The smaller numbers control index 5, and the larger control index 6. 

Example:

You want to have the 5th color be red and the 6th color switched to to be blue.  Set this value to 97 (1+96)

 

The colors are:

1,16 = red

2,32 = orange

3,48 = yellow

4,64 = green

5,80 = cyan

6,96 = blue

7,112 = violet

8,128 = pinkish (Aeon's term)

Options
Parameter 38
Bitmask7F000000
LabelColor index configuration for multi mode (7,8)
DescriptionColor index configuration for multi mode (7,8)
Word Size4
Default Value0
Allowable Range0 to 136
Overview

The colour will be changed from index 1 to index 8 circularly when your bulb is in Multi colour mode.

This is value 1, the MSB.  It controls indexes 7 and 8

Values are additive.  The smaller numbers control index 7, and the larger control index 8. 

Example:

You want to have the 7th color be red and the 8th color switched to to be blue.  Set this value to 97 (1+96)

 

The colors are:

1,16 = red

2,32 = orange

3,48 = yellow

4,64 = green

5,80 = cyan

6,96 = blue

7,112 = violet

8,128 = pinkish (Aeon's term)

 

Options
Parameter 80
Bitmask
LabelEnable notifications
Descriptionset send notifications type for Group 1
Word Size1
Default Value0
Allowable Range0 to 255
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelHail
Option Overview
Option Value2
Option LabelBasic
Option Overview
Parameter 252
Bitmask
LabelLock configuration
DescriptionEnable/disable the ability to configure the device.
Word Size1
Default Value0
Allowable Range0 to 255
Overview
Options
Option Value0
Option Labeldisabled
Option Overview
Option Value1
Option Labelenabled
Option Overview

Association Groups

Group ID1
LabelGroup 1
Description
Maximum Nodes5
ControllerYes
Overview
Group ID2
LabelGroup 2
Description
Maximum Nodes5
ControllerYes
Overview

Endpoints

Endpoint NameEndpoint 0
Endpoint Number0
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_MULTILEVEL
Specific ClassSPECIFIC_TYPE_POWER_SWITCH_MULTILEVEL
Command Classes
Class Ver Basic NIF Sec UnSec
NO_OPERATION 1
BASIC 1
SWITCH_MULTILEVEL 2
Dimmer
SWITCH_ALL
SCENE_ACTIVATION 1
METER
COLOR 2
Color Control
Color Temperature
CONFIGURATION 1
MANUFACTURER_SPECIFIC 1
ASSOCIATION 1
VERSION 1

Reference Documents

Engineering Manual 13-LED-Bulb.pdf
Product Image zw098.jpg

First added to database on 2018-02-11 15:50:50. Current released version is 4.
Last updated by Bruce Osborne on 2019-07-22 01:05:06 (1 month ago).
Approved on 2019-07-22 07:14:32, and last exported on 2019-07-22 07:14:34.

Comments  
# Peter Bengtsson 2017-02-06 23:26
Please remove configuration parameter 0. It was added by me by mistake. Edited the wrong item *sigh*. Sorry, my bad.
Reply | Reply with quote | Quote
Add comment