Device Overview

ManufacturerAEON Labs
Manufacturer ID0086
NameZW078
Device DescriptionHeavy Duty Switch
CategoryWall Switch
References (Type:Id)0003:004E,0103:004E,0203:004E,1A03:004E
Firmware VersionsAll
Protocol Version
Library TypeUnknown
Always ListeningYes
Frequently ListeningNo
Supports RoutingYes
Supports BeamingNo
Supports SecurityNo
Maximum Data Rate
Device Overview

Wall mounted switch for high current appliances, up to 40A. Power reporting.

Inclusion Information

If you’re using a Z-Stick:

  1. Decide on where you want your Heavy Duty Smart Switch to be placed and set it up as per the Quick Start guide steps 1 to 5. Its Status LED will begin to blink.
  2. If your Z-Stick is plugged into a gateway or a computer, unplug it.
  3. Take your Z-Stick to your Heavy Duty Smart Switch.
  4. Press the Action Button on your Z-Stick.
  5. Press the Action Button on your Heavy Duty Smart Switch.
  6. If your switch has been successfully linked to your Z-Wave network, its Status LED will no longer blink. If the linking was unsuccessful, the Status LED continues to blink. Repeat the above steps.
  7. Press the Action Button on your Z-Stick to take it out of installation mode
Exclusion Information
  1. Unplug the Z-Stick from your gateway or computer.
  2. Take your Z-Stick to your Heavy Duty Smart Switch.
  3. Press the Action Button on your Z-Stick.
  4. Press the Action Button on your Heavy Duty Smart Switch.
  5. If your Heavy Duty Smart Switch has been successfully removed from your network, its Status LED will blink. If the removal was unsuccessful, its Status LED will not blink.
  6. Press the Action Button on your Z-Stick to take it out of removal mode.
Usage Information
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_BINARY
Specific ClassSPECIFIC_TYPE_POWER_SWITCH_BINARY
Unique Referencezw078

Configuration Parameters

Parameter 3
Bitmask
LabelCurrent Overload Protection
DescriptionLoad will be closed when current more that 39.5A and time more 5 seconds
Word Size1
Default Value0
Allowable Range0 to 255
Overview
Options
Option Value0
Option LabelDeactivate
Option Overview
Option Value1
Option LabelActivate
Option Overview
Parameter 20
Bitmask
LabelOutput Load Status
DescriptionConfigure the output load status after re‐power on.
Word Size1
Default Value0
Allowable Range0 to 255
Overview
Options
Option Value0
Option LabelLast Status
Option Overview
Option Value1
Option LabelAlways ON
Option Overview
Option Value2
Option LabelAlways OFF
Option Overview
Parameter 80
Bitmask
LabelNotification on Status Change
DescriptionSend to group 1 on load change
Word Size1
Default Value0
Allowable Range0 to 255
Overview

Parameter to Enable to send notification to associated devices (Group 1) when the state of Micro Smart Switch's load changed

Options
Option Value0
Option LabelDeactivate
Option Overview
Option Value1
Option LabelHail CC Sent
Option Overview
Option Value2
Option LabelBasic CC Report Sent
Option Overview
Parameter 90
Bitmask
LabelSend report on value change
DescriptionToggle automated report sending on change
Word Size1
Default Value0
Allowable Range0 to 255
Overview

Parameter to Enable/Disable automated sending of a Report triggered by minimal change of value.

Options
Option Value0
Option LabelDeavtivate
Option Overview
Option Value1
Option LabelActivate
Option Overview
Parameter 91
Bitmask
LabelMinimum Change to send Report (Watt)
DescriptionThe value represents the minimum change in Wattage for a Report to be sent.
Word Size2
Default Value25
Allowable Range0 to 65535
Overview
Options
Parameter 92
Bitmask
LabelMinimum Change to send Report (%)
DescriptionPercent change in wattage to send report
Word Size1
Default Value5
Allowable Range0 to 255
Overview

The value represents the minimum change in Wattage Percent for a report to be sent.

Options
Parameter 101
Bitmask
Labelreports to send automatically
DescriptionSee overview
Word Size4
Default Value4
Allowable Range0 to 65535
Overview

The value is a combination number made up of the sum of the values for the individual parameters.                                                       

The parameters have the values: KWH=8, Wattage=4, Current=2, Voltage=1.                          

Options
Parameter 102
Bitmask
Labelwhich reports to send to group 2
Descriptionsee overview
Word Size4
Default Value8
Allowable Range0 to 65535
Overview

The value is a combination number made up of the sum of the values for the individual parameters.                                                       

The parameters have the values: KWH=8, Wattage=4, Current=2, Voltage=1.                          

Options
Parameter 103
Bitmask
Labelwhich reports to send to group 3
Descriptionsee overview
Word Size4
Default Value0
Allowable Range0 to 65535
Overview

The value is a combination number made up of the sum of the values for the individual parameters.                                                       

The parameters have the values: KWH=8, Wattage=4, Current=2, Voltage=1.                          

Options
Parameter 111
Bitmask
LabelInterval to send out reports of group 1
Description
Word Size4
Default Value3
Allowable Range1 to 2678400
Overview
Options
Parameter 112
Bitmask
LabelInterval to send out reports of group 2
Description
Word Size4
Default Value600
Allowable Range1 to 2678400
Overview
Options
Parameter 113
Bitmask
LabelInterval to send out reports of group 3
Description
Word Size4
Default Value600
Allowable Range1 to 2678400
Overview
Options

Association Groups

Group ID1
LabelGroup 1
Description
Maximum Nodes5
ControllerYes
Overview

The Node IDs in Group 1 will receive Hail Command/Basic report (configurable) when Heavy Duty Smart Switch Gen5's level changed.

Group ID2
LabelGroup 2
Description
Maximum Nodes5
ControllerNo
Overview

When the Heavy Duty Smart Switch Gen5 receives the commands Basic Set, Switch Binary Set, or Scene Activation Set it will forward the commands to all node IDs (in Group 2).

Endpoints

Endpoint NameEndpoint 0
Endpoint Number0
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_BINARY
Specific ClassSPECIFIC_TYPE_POWER_SWITCH_BINARY
Command Classes
Class Ver Basic NIF Sec UnSec
BASIC 1
SWITCH_BINARY 1
Switch
SWITCH_ALL 1
SCENE_ACTIVATION 1
SCENE_ACTUATOR_CONF 1
SENSOR_MULTILEVEL 5
Sensor (internal temperature)
METER 3
Electric meter (kWh)
Electric meter (amps)
Electric meter (volts)
Electric meter (watts)
Reset Meter
CRC_16_ENCAP 1
ASSOCIATION_GROUP_INFO 1
DEVICE_RESET_LOCALLY 1
ZWAVE_PLUS_INFO 2
CONFIGURATION 1
MANUFACTURER_SPECIFIC 2
POWERLEVEL 1
HAIL 1
ASSOCIATION 2
VERSION 2
MARK 1

Reference Documents

Engineering Spec Engineering-Spec---Aeon-Labs-Heavy-Duty-Smart-Switch-Gen5.pdf
Product Image aeotec-zw078.jpg

First added to database on 2018-04-27 17:46:54. Current released version is 4.
Last updated by Dmitry on 2019-06-05 21:14:59 (3 months ago).
Approved on 2019-06-06 06:48:11, and last exported on 2019-06-06 06:48:14.

Comments  
# Dan Mize 2018-12-04 23:12
Please delete parameter 120, label: Delete, and re-publish.
Reply | Reply with quote | Quote
Add comment