Please note that editing on this site is now closed. We have moved to a new site right across the road at OpenSmartHouse. The new site offers a better user experience and existing users already registered here with permission to edit the database have been migrated and should be able to log on using the request password link.
Goto this device in the new site

Device Overview

ManufacturerAEON Labs
Manufacturer ID0086
NameZW096
Device DescriptionSmart Switch 6
CategoryPower Outlet
References (Type:Id)0003:0060,0103:0060,0203:0060,1D03:0060
Firmware VersionsAll
Protocol Version3.099
Library TypeLIB_SLAVE_ENHANCED
Always ListeningYes
Frequently ListeningNo
Supports RoutingYes
Supports BeamingYes
Supports SecurityNo
Maximum Data Rate40000
Device Overview

Aeon Labs Smart Switch is a Z-Wave power binary switch device based on Z-Wave enhanced 232 slave library V6.51.06.

Its surface has the Smart RGB LEDs on, which can be used for indicating the output load status, the strength of wireless signal. You can also configure its indication colour according to your favour.

It can be included and operated in any Z-wave network with other Z-wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

It is also a security Z-wave device and supports the Over The Air (OTA) feature for the product’s firmware upgrade.
As soon as Smart Switch is removed from a z-wave network it will be restored into default factory setting.

Reset Smart Switch to factory Default:

  1. Make sure the Smart Switch has been connected to the power supply.
  2. Press and hold the Z-wave button for 20 seconds.
  3. If holding time more than one second, the LED will blink faster and faster. If holding time more than 20seconds, the green LED will be on for 2 seconds and then remain colorful gradient status, it indicates reset success, otherwise please repeat step 2.

Note:

  1. This procedure should only be used when the primary controller is inoperable.
  2. Reset Smart Switch to factory default settings will: sets the Smart Switch to not in Z-Wave network state; delete the Association setting, power measure value, Scene Configuration Settings and restore the Configuration setting to the default
Inclusion Information

Add Smart Switch into a z-wave network:

  1. Insert the Smart Switch to power socket, The purple LED will be colorful gradient status.
  2. Let the primary controller into inclusion mode (If you don’t know how to do this, refer to its manual).
  3. Press the Action button.
  4. If the inclusion success, Smart Switch LED will be solid. Otherwise, the LED will remain colorful gradient status, in which you need to repeat the process from step 2.
Exclusion Information

Remove Smart Switch from a z-wave network:

  1. Insert the Smart Switch to power socket, The Smart Switch LED will be solid.
  2. Let the primary controller into remove mode (If you don’t know how to do this, refer to its manual).
  3. Press the Action button.
  4. If the remove is successful, Smart Switch LED will blink slowly. If Smart Switch LED still be solid, please repeat the process from step 2.
Usage Information
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_BINARY
Specific ClassSPECIFIC_TYPE_POWER_SWITCH_BINARY
Unique Referencezw096

Configuration Parameters

Parameter 3
Bitmask
LabelCurrent overload protection enable
DescriptionCurrent overload protection enable
Word Size1
Default Value0
Allowable Range0 to 1
Overview

Current Overload Protection. Load will be closed when the Current overrun (US: 15.5A, other country: 16.2A) and the time more than 2 minutes (0=disabled, 1=enabled).

Options
Option Value0
Option Labeldisabled
Option Overview
Option Value1
Option Labelenabled
Option Overview
Parameter 20
Bitmask
LabelOutput load after re-power
DescriptionConfigure the output load status after re‐power
Word Size1
Default Value0
Allowable Range0 to 2
Overview

Configure the output load status after re-power on
(0=last status, 1=always on, 2=always off)

Options
Option Value0
Option Labellast status
Option Overview
Option Value1
Option Labelalways on
Option Overview
Option Value2
Option Labelalways off
Option Overview
Parameter 33
Bitmask
LabelRGB LED color testing
DescriptionSet the RGB LED color value for testing.
Word Size4
Default Value0
Allowable Range0 to 0
Overview

Value1: Reserved

Value2: Red value

Value3: Green value

Value4: Blue value

Options
Parameter 80
Bitmask
LabelEnable send to associated devices
DescriptionEnable to send notifications to Group 1
Word Size1
Default Value0
Allowable Range0 to 2
Overview

Enable to send notifications to associated devices (Group 1) when the state of Micro Switch’s load changed (0=nothing, 1=hail CC, 2=basic CC report).

Options
Option Value0
Option Labelnothing
Option Overview
Option Value1
Option Labelhail CC
Option Overview
Option Value2
Option Labelbasic CC report
Option Overview
Parameter 81
Bitmask
LabelConfigure LED state
DescriptionConfigure the state of the LED
Word Size1
Default Value0
Allowable Range0 to 2
Overview

Configure the state of LED when it is in 3 modes below:

  • 0= The LED will follow the status (on/off) of its load (Energy mode).
  • 1= When the state of Switch’s load changed, The LED will follow the status (on/off) of its load, but the red LED will turn off after 5 seconds if there is no any switch action (momentary indicate mode).
  • 2= Night light mode.
Options
Option Value0
Option LabelLED follows load
Option Overview
Option Value1
Option LabelLED follows load for 5 seconds
Option Overview
Option Value2
Option LabelNight light mode
Option Overview
Parameter 83 [ADVANCED]
Bitmask
LabelColor in night light mode
Description
Word Size3
Default Value0
Allowable Range0 to 16777215
Overview
Options
Parameter 83
Bitmask000000FF
LabelBlue night light color value
DescriptionBlue night light color value
Word Size3
Default Value221
Allowable Range0 to 255
Overview

Value for parameter 83, night light blue color

Options
Parameter 83
Bitmask0000FF00
LabelGreen night light color value
DescriptionGreen night light color value
Word Size3
Default Value160
Allowable Range0 to 255
Overview

Green color value for parameter 83, night light mode.

Options
Parameter 83
Bitmask00FF0000
LabelRed night light color value
DescriptionConfigure the RGB value when it is in Night light mode
Word Size3
Default Value221
Allowable Range0 to 255
Overview

Configure the RGB value when it is in Night light mode.
Value1: Red color value
Value2: Green color value
Value3: Blue color value

defaults:

Value1=0xDD
Value2=0xA0
Value3=0xDD

Options
Parameter 84 [ADVANCED]
Bitmask
LabelColor in energy mode
Description
Word Size3
Default Value0
Allowable Range0 to 16777215
Overview
Options
Parameter 84
Bitmask000000FF
LabelGreen brightness in energy mode (%)
DescriptionGreen brightness in energy mode (%)
Word Size3
Default Value50
Allowable Range0 to 100
Overview

Configure the brightness level of RGB LED (0%-100%) when
it is in Energy Mode/momentary indicate mode.
Value1: green color value.
Value2: yellow color value.
Value3: red color value.

Options
Parameter 84
Bitmask0000FF00
LabelYellow brightness in energy mode (%)
DescriptionYellow brightness in energy mode (%)
Word Size3
Default Value50
Allowable Range0 to 100
Overview
Options
Parameter 84
Bitmask00FF0000
LabelRed brightness in energy mode (%)
DescriptionRed brightness in energy mode (%)
Word Size3
Default Value50
Allowable Range0 to 100
Overview
Options
Parameter 90
Bitmask
LabelEnable items 91 and 92
DescriptionEnables/disables parameter 91 and 92
Word Size1
Default Value1
Allowable Range0 to 1
Overview

Enables/disables parameter 91 and 92 below (1=enabled, 0=disabled).

Options
Option Value0
Option Labeldisabled
Option Overview
Option Value1
Option Labelenabled
Option Overview
Parameter 91
Bitmask
LabelWattage Threshold
Descriptionminimum change in wattage to trigger
Word Size2
Default Value25
Allowable Range0 to 60000
Overview

The value here represents minimum change in wattage (in
terms of wattage) for a REPORT to be sent (Valid values 0-
60000).

Options
Parameter 92
Bitmask
LabelWattage Percent Change
Descriptionminimum change in wattage percent
Word Size1
Default Value5
Allowable Range0 to 100
Overview

The value here represents minimum change in wattage
percent (in terms of percentage) for a REPORT to be sent
(Valid values 0-100).

Options
Parameter 100
Bitmask
LabelSet 101‐103 to default.
DescriptionSet 101‐103 to default.
Word Size1
Default Value0
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelFalse
Option Overview
Option Value1
Option LabelTrue
Option Overview
Parameter 101
Bitmask
LabelValues to send to group 1
DescriptionWhich reports need to send in Report group 1
Word Size4
Default Value4
Allowable Range0 to 15
Overview
Options
Option Value0
Option LabelNothing
Option Overview
Option Value1
Option LabelVoltage
Option Overview
Option Value2
Option LabelCurrent
Option Overview
Option Value4
Option LabelWattage
Option Overview
Option Value8
Option LabelkWh
Option Overview
Option Value15
Option LabelAll Values
Option Overview
Parameter 102
Bitmask
LabelValues to send to group 2
DescriptionWhich reports need to send in Report group 2
Word Size4
Default Value8
Allowable Range0 to 15
Overview
Options
Option Value0
Option LabelNothing
Option Overview
Option Value1
Option LabelVoltage
Option Overview
Option Value2
Option LabelCurrent
Option Overview
Option Value4
Option LabelWattage
Option Overview
Option Value8
Option LabelkWh
Option Overview
Option Value15
Option LabelAll Values
Option Overview
Parameter 103
Bitmask
LabelValues to send to group 3
DescriptionWhich reports need to send in Report group 3
Word Size4
Default Value0
Allowable Range0 to 15
Overview
Options
Option Value0
Option LabelNothing
Option Overview
Option Value1
Option LabelVoltage
Option Overview
Option Value2
Option LabelCurrent
Option Overview
Option Value4
Option LabelWattage
Option Overview
Option Value8
Option LabelkWh
Option Overview
Option Value15
Option LabelAll Values
Option Overview
Parameter 110
Bitmask
LabelSet 111‐113 to default.
DescriptionSet 111‐113 to default.
Word Size1
Default Value0
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelFalse
Option Overview
Option Value1
Option LabelTrue
Option Overview
Parameter 111
Bitmask
LabelTime interval for sending to group 1
DescriptionGroup 1 automatic update interval
Word Size4
Default Value3
Allowable Range1 to 2147483647
Overview

The time interval of sending Report group 1 (Valid values 0x01-0xFFFFFFFF).

Default value is 3

Note: Only up to 0x7fffffff is currently supported

Options
Parameter 112
Bitmask
LabelTime interval for sending to group 2
DescriptionGroup 2 automatic update interval
Word Size4
Default Value600
Allowable Range1 to 2147483647
Overview

The time interval of sending Report group 1 (Valid values 0x01-0xFFFFFFFF).

Default value is 600

Note: Only up to 0x7fffffff is currently supported

Options
Parameter 113
Bitmask
LabelTime interval for sending to group 3
DescriptionGroup 3 automatic update interval
Word Size4
Default Value600
Allowable Range1 to 2147483647
Overview

The time interval of sending Report group 1 (Valid values 0x01-0xFFFFFFFF).

Default value is 600

Note: Only up to 0x7fffffff is currently supported

Options
Parameter 252
Bitmask
LabelConfiguration Locked
DescriptionEnable/disable Configuration Locked (0 =disable, 1 = enable).
Word Size1
Default Value0
Allowable Range0 to 1
Overview

Enable/disable Configuration Locked (0 =disable, 1 =enable).

Options
Option Value0
Option Labeldisabled
Option Overview
Option Value1
Option Labelenabled
Option Overview
Parameter 255 [ADVANCED]
Bitmask
LabelRESET
DescriptionReset the device to defaults
Word Size1
Default Value0
Allowable Range0 to 1
Overview

Reset configuration set up to default setting.

Options

Association Groups

Group ID1
LabelGroup 1
Descriptionload notification type (lifeline)
Maximum Nodes5
ControllerYes
Overview

When the state of Smart Switch (turn on/off the load ) is changed:

  1. Set Configuration parameter 80 to 0 Reserved (Default).
  2. Set Configuration parameter 80 to 1 Send Hail CC.
  3. Set Configuration parameter 80 to 2: Send the Basic Report.
Group ID2
LabelGroup 2
Descriptionforwarding basic set (retransmit)
Maximum Nodes5
ControllerNo
Overview

Forward the Basic Set, Switch Binary Set to associated nodes in Group 2 when the Smart Switch receives the Basic Set, Switch Binary Set commands from main controller.

Endpoints

Endpoint NameEndpoint 0
Endpoint Number0
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_BINARY
Specific ClassSPECIFIC_TYPE_POWER_SWITCH_BINARY
Command Classes
Class Ver Basic NIF Sec UnSec
NO_OPERATION 1
BASIC 1
SWITCH_BINARY 1
Switch
SWITCH_ALL 1
METER 3
Electric meter (kWh)
Electric meter (amps)
Electric meter (volts)
Electric meter (watts)
Reset Meter
COLOR 1
Color
CONFIGURATION 1
MANUFACTURER_SPECIFIC 1
ASSOCIATION 1
VERSION 1

Reference Documents

User Manual 3-Smart-Switch-6.pdf
Product Image ZW096.jpg

First added to database on 2018-03-02 22:56:38. Current released version is 4.
Last updated by Super User on 2020-01-04 12:22:08 (9 months ago).
Approved on 2020-01-04 13:02:26, and last exported on 2020-01-04 13:02:31.

Comments  
# Peter Stapf 2020-01-04 10:35
Sorry edited wrong device by mistake, will take more care in future
Please remove parameter 2 that I added here

You have no rights to post comments