Device definition contains errors

  • Device has association groups defined, but does not support the ASSOCIATION command class.

These errors must be removed before the device can be approved

  • There are 3 association groups but none are linked to the controller. Is this correct?

Device Overview

ManufacturerLinear Corp
Manufacturer ID014F
NameWD500Z-1
Device DescriptionWall Dimmer Switch
CategoryWall Switch
References (Type:Id)4457:3034
Firmware VersionsAll
Protocol Version3.042
Library TypeLIB_CONTROLLER_BRIDGE
Always ListeningYes
Frequently ListeningNo
Supports RoutingYes
Supports BeamingYes
Supports SecurityNo
Maximum Data Rate40000
Device Overview

500W, 120 VAC Wall Mounted Dimmer

Inclusion Information

Pushing the top or bottom of the switch, the WD500Z-1 allows the user to include or exclude the module from the Z-Wave network.

Exclusion Information

Pushing the top or bottom of the switch, the WD500Z-1 allows the user to include or exclude the module from the Z-Wave network.

Usage Information

The default Command Poll Period of 1500ms can cause issues with state updating properly after a remote command is received due to the transition period between states of around 2.5s. This manifests as a switch turned fully off in real life, but showing as 50% on in the OpenHAB UI.

Recommended to update this setting to > 2500ms to provide more consistent results.

Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_MULTILEVEL
Specific ClassSPECIFIC_TYPE_SCENE_SWITCH_MULTILEVEL
Unique Referencewd500z

Configuration Parameters

Parameter 1
Bitmask
LabelDim Start Level
DescriptionStart dimming from that start level or current level
Word Size1
Default Value1
Allowable Range0 to 255
Overview

A dimmer receiving this command will start dimming from that start level if this bit is set to 0. If the bit is set to 1, the dimmer will ignore the start level and instead start dimming from its current level.

Options
Option Value0
Option LabelUse Start Level
Option Overview
Option Value1
Option LabelIgnore Start Level
Option Overview
Parameter 3
Bitmask
LabelLED Indication
DescriptionThe WD500Z-1 will flicker its LED when it is transmitting to any of its groups.
Word Size1
Default Value0
Allowable Range0 to 255
Overview
Options
Option Value0
Option LabelLED ON - Switch ON
Option Overview

The LED on the WD500Z-1 will turn on when the load attached is ON

Option Value1
Option LabelLED ON - Switch OFF
Option Overview

The LED on the WD500Z-1 will turn on when the load attached is OFF

Parameter 4
Bitmask
LabelInvert Switch
DescriptionReverse switch direction
Word Size1
Default Value0
Allowable Range0 to 255
Overview

To change the top of the switch to OFF and the bottom to ON change parameter to 1.

Options
Option Value0
Option LabelTop-ON, Bottom-OFF
Option Overview
Option Value1
Option LabelBottom-ON, Top-OFF
Option Overview
Parameter 14
Bitmask
LabelEnable Shade Control Group 2
DescriptionThe switch can control shade control devices if this parameter is set to 1
Word Size1
Default Value0
Allowable Range0 to 255
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 15
Bitmask
LabelEnable Shade Control Group 3
DescriptionThe switch can control shade control devices if this parameter is set to 1.
Word Size1
Default Value0
Allowable Range0 to 255
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 19
Bitmask
LabelLED Transmission Indication
DescriptionLED mode while transmitting
Word Size1
Default Value2
Allowable Range0 to 255
Overview

The WD500Z-1 will flicker its LED when it is transmitting to any of its groups.

Parameter set to 0 = not flicker

Parameter set to 1 = flicker the entire time of transmitting

Parameter set to 2 = flicker for only 1 second.

Options
Option Value0
Option LabelDisable Flicker
Option Overview
Option Value1
Option LabelFlicker while transmitting
Option Overview
Option Value2
Option LabelFlicker for 1 second
Option Overview

Association Groups

Group ID1
LabelUNKNOWN!!!
Description
Maximum Nodes5
ControllerNo
Overview
Group ID2
LabelDouble Tap
Description
Maximum Nodes5
ControllerNo
Overview
Group ID3
LabelTriple Tap
Description
Maximum Nodes5
ControllerNo
Overview

Endpoints

Endpoint NameEndpoint 0
Endpoint Number0
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_MULTILEVEL
Specific ClassSPECIFIC_TYPE_SCENE_SWITCH_MULTILEVEL
Command Classes
Class Ver Basic NIF Sec UnSec
NO_OPERATION 1
BASIC 1
SWITCH_MULTILEVEL 1
Dimmer
SWITCH_ALL 1
SCENE_ACTIVATION 1
SCENE_ACTUATOR_CONF
CONFIGURATION 1
MANUFACTURER_SPECIFIC 1
POWERLEVEL 1
VERSION 1

Reference Documents

User Manual WD500Z1-manual.pdf
Product Image wd500z-1.jpg

First added to database on 2018-05-27 17:26:07. Current released version is 5.
Last updated by Super User on 2018-11-03 07:54:07 (8 months ago).
Approved on 2018-11-03 11:42:01, and last exported on 2018-12-09 10:39:49.

Add comment


Security code
Refresh