Device Overview

ManufacturerLinear Corp
Manufacturer ID014F
NameWAPIRZ-1
Device DescriptionPIR Motion Detector
CategoryMotion Detector
References (Type:Id)2002:0203
Firmware VersionsAll
Protocol Version3.067
Library TypeLIB_CONTROLLER_BRIDGE
Always ListeningNo
Frequently ListeningNo
Supports RoutingYes
Supports BeamingNo
Supports SecurityNo
Maximum Data Rate
Device Overview

Wireless Passive Infrared (PIR) Motion Detector

Inclusion Information
  1. Prepare the Controller to include a unit to the network by adding it to a group (method of adding a node to the network). Refer to controller instructions.
  2. If your Controller supports Network Wide Inclusion (NWI) locate the WAPIRZ-1 near the proposed installation location. If not skip to Step 4.
  3. With your Controller in Inclusion mode, you should see an indication on your Controller that the “device was included” in the network. It should display binary switch / Linear. The LED will stop blinking. Skip to Step 10. If the LED does not stop blinking, relocate the WAPIRZ-1 to within 100 feet (line of sight) of a Z-Wave device or your hub and repeat Step 3. If the LED continues to blink, your Controller does not support NWI and continue with Step 4.
  4. Place the WAPIRZ-1 within 3 feet of the Controller.
  5. With your controller in Inclusion mode, depress the Tamper switch for 1 second then release.
  6. You should see an indication on your Controller that the “device was included” in the network. It should display binary switch / Linear. The LED will stop blinking.
  7. The device will appear in the list of Switches.
Exclusion Information
  1. Set up the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the WAPIRZ-1 from the controller.
  2. Press the Tamper switch of WAPIRZ-1 for 1 second and release to be excluded. The LED light will flash continuously when the sensor is in the Exclusion condition.
Wakeup Information

Open the motion detector case to “wake” the unit.

Usage Information
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SENSOR_BINARY
Specific ClassSPECIFIC_TYPE_ROUTING_SENSOR_BINARY
Unique Referencewapirz

Configuration Parameters

Parameter 1
Bitmask
LabelRe-trigger Wait Time
DescriptionRe-trigger Wait Time
Word Size1
Default Value3
Allowable Range1 to 255
Overview

By default, to conserve battery life, after the WAPIRZ-1 detects motion it cannot be re-triggered by motion again for 3 minutes. Each time motion is detected (even during this wait time) the 3 minute timer starts over.

Options

Association Groups

Group ID1
LabelGroup 1
Description
Maximum Nodes5
ControllerYes
Overview

Endpoints

Endpoint NameEndpoint 0
Endpoint Number0
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SENSOR_BINARY
Specific ClassSPECIFIC_TYPE_ROUTING_SENSOR_BINARY
Command Classes
Class Ver Basic NIF Sec UnSec
NO_OPERATION 1
BASIC 1
SENSOR_BINARY 1
Binary Sensor
SENSOR_MULTILEVEL 4
Sensor (temperature)
CONFIGURATION 1
ALARM 1
Motion Alarm
MANUFACTURER_SPECIFIC 1
BATTERY 1
WAKE_UP 2
ASSOCIATION 1
VERSION 1

Reference Documents

Installation Guide WAPIRZ-install.pdf
Product Image WAPIRZ.jpg

First added to database on 2018-04-02 21:51:38. Current released version is 3.
Last updated by Super User on 2018-12-12 09:21:31 (4 months ago).
Approved on 2018-12-12 09:21:35, and last exported on 2018-12-12 09:21:37.

Add comment


Security code
Refresh