• Endpoint 0 contains both switch and dimmer channels. It probably should only include dimmer!
  • There are 4 association groups but none are linked to the controller. Is this correct?

Device Overview

ManufacturerLinear Corp
Manufacturer ID014F
NameWT00Z-1
Device Description3-Way Wall Accessory Switch
CategoryWall Switch
References (Type:Id)5457:3033
Firmware VersionsAll
Protocol Version3.042
Library TypeLIB_SLAVE_ROUTING
Always ListeningYes
Frequently ListeningNo
Supports RoutingYes
Supports BeamingYes
Supports SecurityNo
Maximum Data Rate40000
Device Overview

Radio Frequency (RF) Controlled, 120 VAC, Wall Mounted Transmitter

Inclusion Information

Tap either the top or bottom of the WT00Z-1 once.

Exclusion Information

You  must  first  “RESET  UNIT”  with  your  controller  to  remove  it  from the network. Although adding it to a group includes it in the network, removing  it  from  a  group  does  not  remove  it  from  the  network.  If removed from a group, it functions as a repeater (only). “RESET UNIT” removes it completely from the network.

Usage Information
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_REMOTE
Specific ClassSPECIFIC_TYPE_NOT_USED
Unique Referencewt00z1

Configuration Parameters

Parameter 1
Bitmask
LabelDim Start Level
DescriptionSet Ignore Start Level Bit When Transmitting Dim Commands
Word Size1
Default Value1
Allowable Range0 to 255
Overview

The WT00Z-1 can send Dim commands to Z-Wave enabled dimmers.The Dim command has a start level embedded in it. A dimmer receivingthis command will start dimming from that start level. However, thecommand can be sent so that the dimmer ignores the start level andinstead starts dimming from its current level. By default, the WT00Z-1sends the command so that the dimmer will start dimming from itscurrent dim level rather than the start level embedded in the command.To change this, simply set the configuration parameter to 0.

• Parameter No: 1• 

Length: 1 Byte• 

Valid Values = 0 or 1 (default 1)

NOTE:

Any ACT Z-Wave enabled dimmers have the configuration optionto ignore the start level no matter how you configure the WT00Z-1

 
Options
Option Value0
Option LabelUse Start Level
Option Overview
Option Value1
Option LabelIgnore Start Level
Option Overview
Parameter 2
Bitmask
LabelSuspend Group 4
DescriptionSuspend Group 4
Word Size1
Default Value0
Allowable Range0 to 255
Overview

You may wish to disable transmitting commands to Z-Wave devices that are in Group 4 without “un-associating” those devices from the group. Setting parameter 2 to the value of 1 will stop the WT00Z-1 from transmitting to devices that are “associated” into Group 4.

• Parameter No: 2•

 Length: 1 

Byte• Valid Values = 0 or 1 (default 0

Options
Option Value0
Option LabelEnable Group 4
Option Overview
Option Value1
Option LabelDisable Group 4
Option Overview
Parameter 3
Bitmask
LabelNight Light
DescriptionRelationship between LED and status of devices in Group 1
Word Size1
Default Value0
Allowable Range0 to 255
Overview

The LED on the WT00Z-1 will by default, turn ON when the status of the devices in Group 1 is ON. To make the LED turn ON when the status of Group 1 is OFF set this parameter to a value of 1.

Parameter No: 3• 

Length: 1 Byte• 

Valid Values = 0 or 1 (default 0

Options
Option Value0
Option LabelOn when load is on
Option Overview
Option Value1
Option LabelOn when load is off
Option Overview
Parameter 4
Bitmask
LabelInvert Switch
DescriptionSetting the relationship between the top of the transmitter to ON or OFF
Word Size1
Default Value0
Allowable Range0 to 255
Overview

To change the top of the transmitter to OFF and the bottom of the transmitter to ON, set parameter 4 to 1.

To change back to original settings, set this parameter to the value of 0.

Parameter No: 4

Length: 1 Byte

Valid Values = 0 or 1 (default 0)

Options
Option Value0
Option LabelTop-ON, Bottom-OFF
Option Overview
Option Value1
Option LabelBottom-ON, Top-OFF
Option Overview
Parameter 5
Bitmask
LabelIgnore start level when recieving dim commands
DescriptionIgnore start level when recieving dim commands
Word Size1
Default Value1
Allowable Range0 to 255
Overview

The WT00Z-1 can send Dim commands to Z-Wave enabled dimmers. The Dim command has a start level embedded in it. A dimmer receiving this command will start dimming from that start level. However, the command can be sent so that the dimmer ignores the start level and instead start dimming from its current level. By default, the WT00Z-1 sends the command so that the dimmer will start dimming from its current dim level rather then the start level embedded in the command. To change this, simply set the configuration parameter to 0.

Parameter No: 5•

Length: 1 Byte

Valid Values = 0 or 1 (default 1

Options
Option Value0
Option LabelUse start level
Option Overview
Option Value1
Option LabelIgnore start level
Option Overview
Parameter 7
Bitmask
LabelON/OFF dim rate
Descriptiondim step parameter valid values: 1-99
Word Size1
Default Value3
Allowable Range1 to 99
Overview
Options
Parameter 8
Bitmask
LabelON/OFF dim rate
Descriptiondim timer parameter valid values: 1-255
Word Size1
Default Value10
Allowable Range1 to 255
Overview
Options
Parameter 9
Bitmask
LabelLocal control dim rate
Descriptiondim step parameter valid values: 1-99
Word Size1
Default Value3
Allowable Range1 to 99
Overview
Options
Parameter 10
Bitmask
LabelLocal control dim rate
Descriptiondim timer parameter valid values: 1-255
Word Size1
Default Value10
Allowable Range1 to 255
Overview
Options
Parameter 11
Bitmask
LabelALL ON/ ALL OFF dim rate
Descriptiondim step parameter valid values: 1-99
Word Size1
Default Value3
Allowable Range1 to 99
Overview
Options
Parameter 12
Bitmask
LabelALL ON/ ALL OFF dim rate
Descriptiondim timer parameter valid values: 1-255
Word Size1
Default Value10
Allowable Range1 to 255
Overview
Options
Parameter 13
Bitmask
LabelDisable group 4 during a dim command
DescriptionDisable group 4 during a dim command
Word Size1
Default Value0
Allowable Range0 to 255
Overview

After the WT00Z-1 is commanded to stop dimming when dimming because of the DIM START command, it will then command the Z-Wave devices that are in Group 4 to its new level. To prevent the WT00Z-1 from commanding the Z-Wave devices in Group 4 during this particular occurrence, set Parameter 13 to the value of 1.

Parameter 13

Length: 1 Byte

Valid Values = 0 or 1 (default 0

Options
Option Value0
Option LabelEnable
Option Overview
Option Value1
Option LabelDisable
Option Overview
Parameter 14
Bitmask
LabelEnable Shade Control Group 2
DescriptionThe switch can control shade control devices if this parameter is set to 1.
Word Size1
Default Value0
Allowable Range0 to 255
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 15
Bitmask
LabelEnable Shade Control Group 3
DescriptionThe switch can control shade control devices if this parameter is set to 1.
Word Size1
Default Value0
Allowable Range0 to 255
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 16
Bitmask
LabelEnable Shade Control Group 1
DescriptionThe switch can control shade control devices if this parameter is set to 1.
Word Size1
Default Value0
Allowable Range0 to 255
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 19
Bitmask
LabelLED Transmission Indication
DescriptionLED Transmission Indication
Word Size1
Default Value2
Allowable Range0 to 255
Overview

The WT00Z-1 will flicker its LED when it is transmitting to any of its 4 groups. This flickering can be set to not flicker at all (set to 0), to flicker the entire time it is transmitting (set to 1), or to flicker for only 1 second when it begins transmitting (set to 2). By default, the WT00Z-1 is set to flicker for only 1 second.

Parameter 19

Length: 1 Byte

Valid Values = 0 , 1, 2 (default 2)

Options
Option Value0
Option LabelDisable Flicker
Option Overview
Option Value1
Option LabelFlicker while transmitting
Option Overview
Option Value2
Option LabelFlicker for 1 second
Option Overview
Parameter 20
Bitmask
LabelPoll: minutes
DescriptionFrequency that WT00Z-1 will poll first node in Group 1
Word Size1
Default Value2
Allowable Range1 to 255
Overview

The WT00Z-1 will poll the first node in Group 1 in order to keep itself synchronized with the group if this configuration parameter is set to 1. How often it will poll is configured using this parameter.

Parameter 20

Length: 1 Byte

Valid Values = 1 through 255 (default: 2)

Options
Parameter 21
Bitmask
LabelPoll first node in group 1
DescriptionActivate/Deactivate polling of first node in Group 1
Word Size1
Default Value0
Allowable Range0 to 255
Overview

The WT00Z-1 will poll the first node in Group 1 in order to keep itself synchronized with the group if this configuration parameter is set to 1.

Parameter 21

Length: 1 Byte

Valid Values = 0 , 1 (default 0)

Options
Option Value0
Option LabelDo not poll first node in group
Option Overview
Option Value1
Option LabelPoll first node in group
Option Overview

Association Groups

Group ID1
LabelAssociating Group 1
Description
Maximum Nodes5
ControllerNo
Overview

Nodes in this group are turned ON by tapping the top of the paddle or OFF by tapping the bottom of the paddle. Nodes associated into this group are dimmed by pressing and holding the bottom of the paddle until the desired dim level is reached or brightened by pressing and holding the top of the paddle until the desired level is reached. The LED on the WT00Z-1 will indicate the status of this group ONLY.

Group ID2
LabelAssociating Group 2
Description
Maximum Nodes5
ControllerNo
Overview

Nodes in this group are turned ON by tapping the top of the paddle twice or OFF by tapping the bottom of the paddle twice. Nodes associated into this group are dimmed by tapping the bottom of the paddle once and then pressing and holding the bottom of the paddle until the desired dim level is reached or brightened by tapping the top  of  the  paddle  once  then  pressing and holding the top of the paddle  until the desire level is reached

Group ID3
LabelAssociating Group 3
Description
Maximum Nodes5
ControllerNo
Overview

Nodes in this group are turned ON by tapping the top of the paddle three times or OFF by tapping the bottom of the paddle three times. Nodes associated into this group are dimmed by tapping the bottom of the paddle twice and then pressing and holding the bottom of the paddle until the desired dim level is reached or brightened by tapping the top of the paddle twice then pressing and holding the top of the paddle until the desired level is reached

Group ID4
LabelAssociating Group 4
Description
Maximum Nodes5
ControllerNo
Overview

Nodes in this group are turned ON or OFF or set to a specific dim level when the WT00Z-1 is controlled remotely. You can place up to 5 nodes in each group. If controlling dimmers, for best results, associate the dimmers into the group first

Endpoints

Endpoint NameEndpoint 0
Endpoint Number0
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_REMOTE
Specific Class
Command Classes
Class Ver Basic NIF Sec UnSec
NO_OPERATION 1
BASIC 1
SWITCH_BINARY 1
Switch
SWITCH_MULTILEVEL 1
Dimmer
SWITCH_ALL 1
CONFIGURATION 1
MANUFACTURER_SPECIFIC 1
ASSOCIATION 1
VERSION 1
INDICATOR 1

Reference Documents

User Manual linear-satellite-radio-wt00z-1-users-manual.pdf
Image WT00Z1.jpg

First added to database on 2018-01-05 23:44:02. Current released version is 1.
Last updated by sihui on 2018-07-22 06:38:00 (9 months ago).
Approved on 2018-07-22 06:38:05, and last exported on 2018-12-09 10:39:55.

Add comment


Security code
Refresh