Device Overview

ManufacturerZooz
Manufacturer ID027A
NameZEN31
Device DescriptionRGBW Dimmer for LED Strips
CategoryLight Bulb
References (Type:Id)0902:2000
Firmware VersionsAll
Protocol Version6.004
Library TypeLIB_SLAVE_ENHANCED
Always ListeningYes
Frequently ListeningNo
Supports RoutingYes
Supports BeamingYes
Supports SecurityNo
Maximum Data Rate40000
Device Overview
  • Manual or Z-Wave on/off, brightness, and RGBW color control
  • Perfect for programming your existing RGBW LED strip
  • Energy monitoring in live mode and over time
  • Double tap to full brightness feature + optional scene control
  • Remembers and restores on/off status a?er power failure
  • Built-in Z-Wave Plus signal repeater to extend network range
Inclusion Information

Make sure the RGBW Dimmer is powered up. Click the Z-Wave button 3 times quickly to include the device. The LED will blink yellow to indicate communication with the hub. It will blink green (for non-secure, S0, or S2 unauthenticated inclusion) or magenta (for S2 authenticated) once the device is successfully included to your network. It will blink red if inclusion is not successful

Exclusion Information

Click the Z-Wave button 3 times quickly.

Usage Information
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_MULTILEVEL
Specific ClassSPECIFIC_TYPE_COLOR_TUNABLE_MULTILEVEL
Unique Referencezen31

Configuration Parameters

Parameter 1
Bitmask
LabelStatus after power failure
DescriptionStatus after power failure
Word Size1
Default Value0
Allowable Range0 to 2
Overview
Options
Option Value0
Option LabelForced to OFF
Option Overview
Option Value1
Option LabelRestore status
Option Overview
Option Value2
Option LabelForced to ON
Option Overview
Parameter 20 [ADVANCED]
Bitmask
LabelSwitch / Input type for IN1
DescriptionSwitch / Input type for IN1
Word Size1
Default Value2
Allowable Range0 to 4
Overview
Options
Option Value0
Option LabelAnalog sensor with no pull-up
Option Overview
Option Value1
Option LabelAnalog sensor with pull-up
Option Overview
Option Value2
Option LabelMomentary switch
Option Overview
Option Value3
Option LabelToggle switch (change on toggle)
Option Overview

Toggle switch (state changes whenever the switch is toggled)

Option Value4
Option LabelToggle switch (Up = ON, Down = OFF)
Option Overview
Parameter 21 [ADVANCED]
Bitmask
LabelSwitch / Input type for IN2
DescriptionSwitch / Input type for IN2
Word Size1
Default Value2
Allowable Range0 to 4
Overview
Options
Option Value0
Option LabelAnalog sensor with no pull-up
Option Overview
Option Value1
Option LabelAnalog sensor with pull-up
Option Overview
Option Value2
Option LabelMomentary switch
Option Overview
Option Value3
Option LabelToggle switch (change on toggle)
Option Overview

 Toggle switch (state changes whenever the switch is toggled)

Option Value4
Option LabelToggle switch (Up = ON, Down = OFF)
Option Overview
Parameter 22 [ADVANCED]
Bitmask
LabelSwitch / Input type for IN3
DescriptionSwitch / Input type for IN3
Word Size1
Default Value2
Allowable Range0 to 4
Overview
Options
Option Value0
Option LabelAnalog sensor with no pull-up
Option Overview
Option Value1
Option LabelAnalog sensor with pull-up
Option Overview
Option Value2
Option LabelMomentary switch
Option Overview
Option Value3
Option Label Toggle switch (change on toggle)
Option Overview

 Toggle switch (state changes whenever the switch is toggled)

Option Value4
Option LabelToggle switch (Up = ON, Down = OFF)
Option Overview
Parameter 23 [ADVANCED]
Bitmask
LabelSwitch / Input type for IN4
DescriptionSwitch / Input type for IN4
Word Size1
Default Value2
Allowable Range0 to 4
Overview
Options
Option Value0
Option LabelAnalog sensor with no pull-up
Option Overview
Option Value1
Option LabelAnalog sensor with pull-up
Option Overview
Option Value2
Option LabelMomentary switch
Option Overview
Option Value3
Option Label Toggle switch (change on toggle)
Option Overview

 Toggle switch (state changes whenever the switch is toggled)

Option Value4
Option LabelToggle switch (Up = ON, Down = OFF)
Option Overview
Parameter 40
Bitmask00000001
LabelClick/toggle once to trigger a scene (IN1)
DescriptionAssign scene activation trigger for IN1 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 40
Bitmask00000002
LabelClick/toggle twice to trigger a scene (IN1)
DescriptionAssign scene activation trigger for IN1 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 40
Bitmask00000004
LabelClick/toggle three times to trigger a scene (IN1)
DescriptionAssign scene activation trigger for IN1 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 40
Bitmask00000008
LabelHold and release to trigger a scene (IN1)
DescriptionAssign scene activation trigger for IN1 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 41
Bitmask00000001
LabelClick/toggle once to trigger a scene (IN2)
DescriptionAssign scene activation trigger for IN2 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 41
Bitmask00000002
LabelClick/toggle twice to trigger a scene (IN2)
DescriptionAssign scene activation trigger for IN2 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 41
Bitmask00000004
LabelClick/toggle three times to trigger a scene (IN2)
DescriptionAssign scene activation trigger for IN2 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 41
Bitmask00000008
LabelHold and release to trigger a scene (IN2)
DescriptionAssign scene activation trigger for IN2 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 42
Bitmask00000001
LabelClick/toggle once to trigger a scene (IN3)
DescriptionAssign scene activation trigger for IN3 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 42
Bitmask00000002
LabelClick/toggle twice to trigger a scene (IN3)
DescriptionAssign scene activation trigger for IN3 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 42
Bitmask00000004
LabelClick/toggle three times to trigger a scene (IN3)
DescriptionAssign scene activation trigger for IN3 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 42
Bitmask00000008
LabelHold and release to trigger a scene (IN3)
DescriptionAssign scene activation trigger for IN3 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 43
Bitmask00000001
LabelClick/toggle once to trigger a scene (IN4)
DescriptionAssign scene activation trigger for IN4 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 43
Bitmask00000002
LabelClick/toggle twice to trigger a scene (IN4)
DescriptionAssign scene activation trigger for IN4 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 43
Bitmask00000004
LabelClick/toggle three times to trigger a scene (IN4)
DescriptionAssign scene activation trigger for IN4 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 43
Bitmask00000008
LabelHold and release to trigger a scene (IN4)
DescriptionAssign scene activation trigger for IN4 terminal
Word Size1
Default Value1
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview
Parameter 62
Bitmask
LabelPower report frequency
DescriptionPower report frequency
Word Size2
Default Value3600
Allowable Range30 to 32400
Overview

Allowed values: 0 (disabled) or 30 - 32400 seconds

Default: 3600 seconds (1 hour)

Options
Option Value0
Option LabelDisable
Option Overview
Parameter 63
Bitmask
LabelVoltage Reporting / Trigger Threshold
DescriptionChoose how you want your RGBW Dimmer to report voltage changes.
Word Size2
Default Value5
Allowable Range0 to 100
Overview

Choose how you want your RGBW Dimmer to report voltage changes from the connected analog sensors and trigger status change on the output. The number entered as value corresponds to decimal values in voltage change. So if 5 is entered by default, the RGBW Dimmer will report any change in voltage of the connected sensor over 0.5 V. This setting is only in effect if at least one of Parameters 20 – 23 is set to value 0 or 1 (input is set to analog sensor mode).

Allowed range: 0 -100

Default: 5

Options
Parameter 64
Bitmask
LabelAnalog Sensor Report Frequency
DescriptionChoose how often you want your RGBW Dimmer to report voltage changes.
Word Size2
Default Value0
Allowable Range30 to 32400
Overview

Choose how often you want your RGBW Dimmer to report voltage changes from the connected analog sensors to your hub. The number entered as value corresponds to the number of seconds. So if 3600 isentered as value, the RGBW Dimmer will report voltage from connected analog sensors every hour (independent of the threshold set in parameter 63). Voltage reports are sent in at least 30-second intervals. This setting is only in effect if at least one of Parameters 20 – 23 is set to value 0 or 1 (input is set to analog sensor mode).

Allowed values: 0 (disabled) or 30 - 32400 seconds

Default: 0 (disabled)

Options
Option Value0
Option LabelDisable
Option Overview
Parameter 65
Bitmask
LabelEnergy report threshold
DescriptionEnergy report threshold
Word Size2
Default Value10
Allowable Range0 to 500
Overview

Choose how you want your RGBW Dimmer to report energy use (kWh) to your hub. The number entered as value corresponds to decimal values in energy usage change. So if 10 is entered by default, the RGBW Dimmer will report any change in energy use over 0.1 kWh. Energy reports are sent in at least 30-second intervals.

Allowed values: 0 (disabled) or 1 - 500 (0.01 - 5.00 kWh)

Default: 10 (0.1 kWh)

Options
Parameter 66
Bitmask
LabelEnergy report frequency
DescriptionEnergy report frequency
Word Size2
Default Value3600
Allowable Range30 to 32400
Overview

Choose how often you want your RGBW Dimmer to report energy (kWh) to your controller. The number entered as value corresponds to the number of seconds. So if 3600 is entered by default, the RGBW Dimmer will report energy use every hour(independent of the threshold set in parameter 65). Energy reports are sent in at least 30-second intervals.

Allowed values: 0 (disabled) or 30 - 32400 seconds

Default: 3600 seconds (1 hour)

Options
Option Value0
Option LabelDisable
Option Overview
Parameter 150
Bitmask
LabelRGBW / HSB Wall Switch Mode
DescriptionChoose how switches connected to the input terminals control your LED strip
Word Size1
Default Value0
Allowable Range0 to 1
Overview

Choose how switches connected to the input terminals control your LED strip. In the default RGBW mode, each switch connected to each input terminal controls the RGBW channels separately (so IN1 for red, IN2 for green, etc) with a single click for ON/OFF, double click to full brightness, and press-and-hold to dim (momentary switches only). In the HSB mode, IN1 controls hue, IN2 – saturation, IN3 – brightness, IN4 – white with single click for last set value or value 0, double click to max value, and press-and-hold to set custom value.

Options
Option Value0
Option LabelRGBW mode
Option Overview
Option Value1
Option LabelHSB mode
Option Overview
Parameter 151
Bitmask
LabelRamp Rate
DescriptionAdjust the fade-in/fade-out effect for ON/OFF operation
Word Size2
Default Value3
Allowable Range0 to 254
Overview

Adjust the ramp rate for your RGBW dimmer (fade-in/fade-out effect for ON/OFF operation). Values correspond to the number of seconds it takes for the dimmer to reach full brightness or turn OFF when operated from the connected wall switch.

You can also set the physical ramp rate in minutes instead of seconds by using a value between 128-254. For minutes, subtract 127 from the value (e.g. a value of 132 corresponds to 132 - 127 = 5 minutes).

Allowed values: 0 (instant ON/OFF), 1 - 127 seconds, or 128 - 254 (1 - 127 minutes)

Options
Parameter 152
Bitmask
LabelRamp Rate (remote)
DescriptionAdjust the ramp rate of your RGBW dimmer when operated remotely through openHAB
Word Size2
Default Value3
Allowable Range0 to 254
Overview

Adjust the ramp rate for your RGBW dimmer (fade-in / fade-out effect for on / off operation). Values correspond to the number of seconds it take for the dimmer to reach full brightness or turn off when operated from the connected wall switch.

You can also set the Z-Wave ramp rate in minutes instead of seconds by using a value between 128-254. For minutes, subtract 127 from the value (e.g. a value of 132 corresponds to 132 - 127 = 5 minutes).

Allowed values: 0 instant ON/OFF), 1 - 127 seconds, or 128 - 254 (1 - 127 minutes)

Options
Parameter 154
Bitmask000000FF
LabelSingle Click ON Trigger (IN1)
DescriptionSingle Click ON Trigger (IN1)
Word Size4
Default Value255
Allowable Range0 to 99
Overview

Set the status or brightness level triggering other associated devices in your network if the dimmer is turned ON with a single click. Each of the 4 available bytes refers to one channel, starting with IN1 and ending with IN4. This setting applies to basic set and switch multilevel commands sent to associated devices in the appropriate association group.

Allow value: 0 - 99, 255 (ON)

Options
Option Value255
Option LabelON
Option Overview
Parameter 154
Bitmask0000FF00
LabelSingle Click ON Trigger (IN2)
DescriptionSingle Click ON Trigger (IN2)
Word Size4
Default Value255
Allowable Range0 to 99
Overview

Set the status or brightness level triggering other associated devices in your network if the dimmer is turned ON with a single click. Each of the 4 available bytes refers to one channel, starting with IN1 and ending with IN4. This setting applies to basic set and switch multilevel commands sent to associated devices in the appropriate association group.

Allow value: 0 - 99, 255 (ON)

Options
Parameter 154
Bitmask00FF0000
LabelSingle Click ON Trigger (IN3)
DescriptionSingle Click ON Trigger (IN3)
Word Size4
Default Value255
Allowable Range0 to 99
Overview

Set the status or brightness level triggering other associated devices in your network if the dimmer is turned ON with a single click. Each of the 4 available bytes refers to one channel, starting with IN1 and ending with IN4. This setting applies to basic set and switch multilevel commands sent to associated devices in the appropriate association group.

Allow value: 0 - 99, 255 (ON)

Options
Parameter 154
Bitmask7F000000
LabelSingle Click ON Trigger (IN4)
DescriptionSingle Click ON Trigger (IN4)
Word Size4
Default Value255
Allowable Range0 to 99
Overview

Set the status or brightness level triggering other associated devices in your network if the dimmer is turned ON with a single click. Each of the 4 available bytes refers to one channel, starting with IN1 and ending with IN4. This setting applies to basic set and switch multilevel commands sent to associated devices in the appropriate association group.

Allow value: 0 - 99, 255 (ON)

Options
Parameter 157
Bitmask
LabelPreset Programs
DescriptionEnable one of the preset animated color programs to set the mood with a click
Word Size1
Default Value0
Allowable Range0 to 10
Overview

0 - Preset programs disabled

6 - Fireplace

7 - Storm

8 - Rainbow

9 - Polar lights

10 - Police (strobing red, white and blue)

Options
Option Value0
Option LabelPreset programs disabled
Option Overview
Option Value6
Option LabelFireplace
Option Overview
Option Value7
Option LabelStorm
Option Overview
Option Value8
Option LabelRainbow
Option Overview
Option Value9
Option LabelPolar Lights
Option Overview
Option Value10
Option LabelPolice (strobing red, white and blue)
Option Overview

Association Groups

Group ID1
LabelLifeline
Description
Maximum Nodes1
ControllerYes
Overview
Group ID2
LabelGroup 2
DescriptionReserved for association and sync with other Zooz RGBW Dimmers (not for use with other devices).
Maximum Nodes5
ControllerNo
Overview

Reserved for association and sync with other Zooz RGBW Dimmers (not for use with other devices).

Group ID3
LabelGroup 3
DescriptionON/OFF operation sync from input IN1
Maximum Nodes5
ControllerNo
Overview

ON/OFF operation sync from input IN1

Group ID4
LabelGroup 4
DescriptionBrightness (dimming) sync from input IN1
Maximum Nodes5
ControllerNo
Overview

Brightness (dimming) sync from input IN1

Group ID5
LabelGroup 5
DescriptionON/OFF operation sync from input IN2
Maximum Nodes5
ControllerNo
Overview

ON/OFF operation sync from input IN2

Group ID6
LabelGroup 6
DescriptionBrightness (dimming) sync from input IN2
Maximum Nodes5
ControllerNo
Overview

Brightness (dimming) sync from input IN2

Group ID7
LabelGroup 7
DescriptionON/OFF operation sync from input IN3
Maximum Nodes5
ControllerNo
Overview

ON/OFF operation sync from input IN3

Group ID8
LabelGroup 8
DescriptionBrightness (dimming) sync from input IN3
Maximum Nodes5
ControllerNo
Overview

Brightness (dimming) sync from input IN3

Group ID9
LabelGroup 9
DescriptionON/OFF operation sync from input IN4
Maximum Nodes5
ControllerNo
Overview

ON/OFF operation sync from input IN4

Group ID10
LabelGroup 10
DescriptionBrightness (dimming) sync from input IN4
Maximum Nodes5
ControllerNo
Overview

Brightness (dimming) sync from input IN4

Endpoints

Endpoint NameEndpoint 0
Endpoint Number0
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_MULTILEVEL
Specific ClassSPECIFIC_TYPE_COLOR_TUNABLE_MULTILEVEL
Command Classes
Class Ver Basic NIF Sec UnSec
NO_OPERATION 1
BASIC 1
APPLICATION_STATUS 1
SWITCH_MULTILEVEL 3
SENSOR_MULTILEVEL 10
Sensor (voltage)
METER 3
COLOR 3
CRC_16_ENCAP 1
ASSOCIATION_GROUP_INFO 1
DEVICE_RESET_LOCALLY 1
CENTRAL_SCENE 3
Scene Number
ZWAVE_PLUS_INFO 1
MULTI_INSTANCE 2
CONFIGURATION 1
Preset Program
ALARM 8
MANUFACTURER_SPECIFIC 1
POWERLEVEL 1
PROTECTION 2
FIRMWARE_UPDATE_MD 1
ASSOCIATION 2
VERSION 2
MULTI_INSTANCE_ASSOCIATION 3
SECURITY 1
Endpoint NameEndpoint 1
Endpoint Number1
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_MULTILEVEL
Specific ClassSPECIFIC_TYPE_COLOR_TUNABLE_MULTILEVEL
Command Classes
Class Ver Basic NIF Sec UnSec
BASIC
APPLICATION_STATUS 1
SWITCH_MULTILEVEL 3
Dimmer (brightness)
METER 3
Electric meter (watts) 1
Electric meter (kWh) 1
COLOR 3
Color Control
Color Temperature
ASSOCIATION_GROUP_INFO 1
ZWAVE_PLUS_INFO 1
ALARM 8
Alarm (system) 1
Alarm (power) 1
PROTECTION 2
ASSOCIATION 2
MULTI_INSTANCE_ASSOCIATION 3
SECURITY 1
Endpoint NameEndpoint 2
Endpoint Number2
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_MULTILEVEL
Specific ClassSPECIFIC_TYPE_POWER_SWITCH_MULTILEVEL
Command Classes
Class Ver Basic NIF Sec UnSec
BASIC
APPLICATION_STATUS 1
SWITCH_MULTILEVEL 3
Dimmer (red)
ASSOCIATION_GROUP_INFO 1
ZWAVE_PLUS_INFO 1
ASSOCIATION 2
MULTI_INSTANCE_ASSOCIATION 3
SECURITY 1
Endpoint NameEndpoint 3
Endpoint Number3
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_MULTILEVEL
Specific ClassSPECIFIC_TYPE_POWER_SWITCH_MULTILEVEL
Command Classes
Class Ver Basic NIF Sec UnSec
BASIC
APPLICATION_STATUS 1
SWITCH_MULTILEVEL 3
Dimmer (green)
ASSOCIATION_GROUP_INFO 1
ZWAVE_PLUS_INFO 1
ASSOCIATION 2
MULTI_INSTANCE_ASSOCIATION 3
SECURITY 1
Endpoint NameEndpoint 4
Endpoint Number4
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_MULTILEVEL
Specific ClassSPECIFIC_TYPE_POWER_SWITCH_MULTILEVEL
Command Classes
Class Ver Basic NIF Sec UnSec
BASIC
APPLICATION_STATUS 1
SWITCH_MULTILEVEL 3
Dimmer (blue)
ASSOCIATION_GROUP_INFO 1
ZWAVE_PLUS_INFO 1
ASSOCIATION 2
MULTI_INSTANCE_ASSOCIATION 3
SECURITY 1
Endpoint NameEndpoint 5
Endpoint Number5
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_MULTILEVEL
Specific ClassSPECIFIC_TYPE_POWER_SWITCH_MULTILEVEL
Command Classes
Class Ver Basic NIF Sec UnSec
BASIC
APPLICATION_STATUS 1
SWITCH_MULTILEVEL 3
Dimmer (white)
ASSOCIATION_GROUP_INFO 1
ZWAVE_PLUS_INFO 1
ASSOCIATION 2
MULTI_INSTANCE_ASSOCIATION 3
SECURITY 1
Endpoint NameEndpoint 6
Endpoint Number6
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SENSOR_MULTILEVEL
Specific ClassSPECIFIC_TYPE_ROUTING_SENSOR_MULTILEVEL
Command Classes
Class Ver Basic NIF Sec UnSec
BASIC
APPLICATION_STATUS 1
SENSOR_MULTILEVEL 10
ASSOCIATION_GROUP_INFO 1
ZWAVE_PLUS_INFO 1
ASSOCIATION 2
MULTI_INSTANCE_ASSOCIATION 3
SECURITY 1
Endpoint NameEndpoint 7
Endpoint Number7
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SENSOR_MULTILEVEL
Specific ClassSPECIFIC_TYPE_ROUTING_SENSOR_MULTILEVEL
Command Classes
Class Ver Basic NIF Sec UnSec
BASIC
APPLICATION_STATUS 1
SENSOR_MULTILEVEL 10
ASSOCIATION_GROUP_INFO 1
ZWAVE_PLUS_INFO 1
ASSOCIATION 2
MULTI_INSTANCE_ASSOCIATION 3
SECURITY 1
Endpoint NameEndpoint 8
Endpoint Number8
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SENSOR_MULTILEVEL
Specific ClassSPECIFIC_TYPE_ROUTING_SENSOR_MULTILEVEL
Command Classes
Class Ver Basic NIF Sec UnSec
BASIC
APPLICATION_STATUS 1
SENSOR_MULTILEVEL 10
ASSOCIATION_GROUP_INFO 1
ZWAVE_PLUS_INFO 1
ASSOCIATION 2
MULTI_INSTANCE_ASSOCIATION 3
SECURITY 1
Endpoint NameEndpoint 9
Endpoint Number9
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SENSOR_MULTILEVEL
Specific ClassSPECIFIC_TYPE_ROUTING_SENSOR_MULTILEVEL
Command Classes
Class Ver Basic NIF Sec UnSec
BASIC
APPLICATION_STATUS 1
SENSOR_MULTILEVEL 10
ASSOCIATION_GROUP_INFO 1
ZWAVE_PLUS_INFO 1
ASSOCIATION 2
MULTI_INSTANCE_ASSOCIATION 3
SECURITY 1

Reference Documents

Image ZEN31.png
Manual zooz-s2-rgbw-dimmer-zen31-online-manual.pdf

First added to database on -0001-11-30 00:00:00. Current released version is 8.
Last updated by Scott Rushworth on 2020-03-24 05:17:22 (3 months ago).
Approved on 2020-05-09 20:20:41, and last exported on 2020-05-09 20:20:51.

Comments  
# Scott Rushworth 2020-03-24 05:18
Removed extra Channels

You have no rights to post comments