Device Overview

ManufacturerInovelli
Manufacturer ID031E
NameLZW30
Device DescriptionBase model On-Off switch
CategoryWall Switch
References (Type:Id)0004:0001
Firmware VersionsAll
Protocol Version6.004
Library TypeLIB_SLAVE_ENHANCED
Always ListeningYes
Frequently ListeningNo
Supports RoutingYes
Supports BeamingYes
Supports SecurityYes
Maximum Data Rate40000
Device Overview

The Inovelli On/Off switch is a Z-Wave device that controls attached LED, CFL, & Incandescent lighting which can be highly customized to your liking at the switch itself with our unique config button and advanced firmware.

 Configuration/Favorites Button: This switch allows for ultimate customization via the Configuration Button (rather than via a Z-Wave HUB) such as the power on state, LED Indicator Color, LED Indicator Intensity, and LED Indicator Intensity (When Off). 

OTA (Over-the-Air) Enabled: As with all our devices, the switch allows you to receive our latest firmware updates (NOTE: Please make sure your HUB supports this).

Inclusion Information

Now that the switch is physically installed, let’s start the inclusion (pairing) process.

  • Restore power to your switch and if wired properly, the LED bar will light up (should flash a series of colors, then turn blue)
  • Start the inclusion process on your HUB/Gateway
  • Press the config button (A) 3x and the LED bar should pulse blue (if it doesn’t, try pressing the buttons faster or slower) indicating the switch is in inclusion mode. If successful, the switch LED Bar (B) will turn Green. If unsuccessful, the LED Bar will turn RED.
  • Z-Wave Range Check: Easily check whether or not your switch is within range by holding the Config Button (A) for 5-10 seconds. The LED bar will indicate: RED = Not in Range, or = Within Range GREEN (Good Signal).

Final Thoughts / Tips: If you’re having issues pairing your switch, there’s a couple things you can try. The first one is to hold down the config button for 5 seconds until the LED bar indicates RED or GREEN, where RED = Not in Range, or = Within Range GREEN (Good Signal). If the signal is GREEN, then let’s try an exclusion to reset your switch.

Exclusion Information
  • Start the exclusion process on your HUB/Gateway
  • Press, “Remove” and tap the Config button 3x and the LED bar should pulse blue
  • The LED bar should flash GREEN if successful
Usage Information
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_BINARY
Specific ClassSPECIFIC_TYPE_POWER_SWITCH_BINARY
Unique Referencelzw30

Configuration Parameters

Parameter 1
Bitmask
LabelPower On State
DescriptionPower On State
Word Size1
Default Value0
Allowable Range0 to 2
Overview

When power is restored, the switch reverts to either On, Off or last level

0 = Returns to State before Power Outage

1 = On

2 = Off

Options
Option Value0
Option LabelPrior State
Option Overview
Option Value1
Option LabelOn
Option Overview
Option Value2
Option LabelOff
Option Overview
Parameter 2
Bitmask
LabelInvert Switch
DescriptionInvert Switch
Word Size1
Default Value0
Allowable Range0 to 1
Overview

Inverts the switch (tap down = on, tap up = off)

0 = disabled

1 = enabled

Options
Option Value0
Option LabelDisabled
Option Overview

Maintain normal upright function

Option Value1
Option LabelEnabled
Option Overview

Use inverted paddle positions

Parameter 3
Bitmask
LabelAuto Off Timer
DescriptionAuto Off Timer (in seconds)
Word Size2
Default Value0
Allowable Range0 to 32767
Overview

Automatically turns the switch off after x amount of seconds

0 = Disabled

1= 1 second

32767 = 32767 seconds

Options
Parameter 4
Bitmask
LabelAssociation Behaviour
DescriptionAssociation Behaviour
Word Size1
Default Value15
Allowable Range1 to 15
Overview

1 = Local; 2 = 3-Way; 3 = 3-Way + Local; 4 = Z-Wave HUB; 5 = Z-Wave HUB + Local; 6 = Z-Wave HUB + 3-Way; 7 = Z-Wave HUB + Local; 8 = Timer; 9 = Timer + Local; 10 = Timer + 3-Way; 11 = Timer + Local; 12 = Timer + Z-Wave HUB; 13 = Timer + Local; 14 = Timer + Z-Wave HUB; 15 = (Default) All

Options
Parameter 5
Bitmask
LabelLED Indicator Color
DescriptionLED Indicator Color
Word Size2
Default Value170
Allowable Range0 to 255
Overview

0 to 255 Hue Color Circle

170 - Blue - Default

This will set the default color of the LED bar.  Calculated by using a hue color circle (Value / 255 * 360

0 = Red

21 = Orange

42 = Yellow

85 = Green

127 = Cyan

170 = Blue

212 = Violet

234 = Pink

Options
Option Value0
Option LabelRed
Option Overview
Option Value21
Option LabelOrange
Option Overview
Option Value42
Option LabelYellow
Option Overview
Option Value85
Option LabelGreen
Option Overview
Option Value127
Option LabelCyan
Option Overview
Option Value170
Option LabelBlue
Option Overview
Option Value212
Option LabelViolet
Option Overview
Option Value234
Option LabelPink
Option Overview
Parameter 6
Bitmask
LabelLED Indicator Intensity (when on)
DescriptionLED Indicator Intensity (when on)
Word Size1
Default Value5
Allowable Range0 to 10
Overview

0 = Off

1-3 = Low intensity

4-7 = Medium Intensity

8-10 = High Intensity

Options
Option Value0
Option LabelOff
Option Overview
Option Value1
Option Label10 %
Option Overview
Option Value2
Option Label20 %
Option Overview
Option Value3
Option Label30 %
Option Overview
Option Value4
Option Label40 %
Option Overview
Option Value5
Option Label50 %
Option Overview
Option Value6
Option Label60 %
Option Overview
Option Value7
Option Label70 %
Option Overview
Option Value8
Option Label80 %
Option Overview
Option Value9
Option Label90%
Option Overview
Option Value10
Option Label100 %
Option Overview
Parameter 7
Bitmask
LabelLED Indicator Intensity (when Off)
DescriptionLED Indicator Intensity (when Off)
Word Size1
Default Value2
Allowable Range0 to 10
Overview

0 = Off

1-3 = Low Intensity (default)

4-7 = Medium Intensity

8-10 = High Intensity

Options
Option Value0
Option LabelOff
Option Overview
Option Value1
Option Label10 %
Option Overview
Option Value2
Option Label20 %
Option Overview
Option Value3
Option Label30 %
Option Overview
Option Value4
Option Label40 %
Option Overview
Option Value5
Option Label50 %
Option Overview
Option Value6
Option Label60 %
Option Overview
Option Value7
Option Label70 %
Option Overview
Option Value8
Option Label80 %
Option Overview
Option Value9
Option Label90 %
Option Overview
Option Value10
Option Label100 %
Option Overview
Parameter 8
Bitmask
LabelLED Strip Effect
DescriptionCalculated sum of parameters as per overview section
Word Size4
Default Value0
Allowable Range0 to 83823359
Overview

Enter the value that is the sum of:

1) Color value out of 128 (1=red 21=Orange, 42=Yellow, 85=Green, 127=Cyan, 170=Blue, 234=Pink )

2) Level  1 to 10, multiplied by 250

3) Duration in seconds (up to 4 minutes, or use 255 for indefinitely) multiplied by 65536

4) Effect style - (some discrepancy here, likely 1=solid, 2=Fast Blink, 3=Strobe? Slow Blink?, 4=Pulse, 5=?Strobe) - multiplied by 16777216

{4) From Inovelli, supplied values were , 1=Solid, 2= Fast Blink, 2=Strobe, 3=Slow Blink, 4=Pulse.  Note the duplication with value 2.}

Again, add up all these values, and this is the value to supply.

Options

Association Groups

Group ID1
LabelLifeline
Description
Maximum Nodes5
ControllerYes
Overview

Members of this group will receive unsolicited messages related to the status of the switch.
1. Basic Report 2. Device Reset Locally 3. Protection Report

Group ID2
LabelBasic Set
Description
Maximum Nodes5
ControllerNo
Overview
  1. Single press Up button sends BasicSet (0xFF)
    and
  2. Single press Down sends BasicSet (0x00)

Endpoints

Endpoint NameEndpoint 0
Endpoint Number0
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_SWITCH_BINARY
Specific ClassSPECIFIC_TYPE_POWER_SWITCH_BINARY
Command Classes
Class Ver Basic NIF Sec UnSec
NO_OPERATION 1
BASIC 1
APPLICATION_STATUS 1
SWITCH_BINARY 1
Switch
ASSOCIATION_GROUP_INFO 1
DEVICE_RESET_LOCALLY 1
ZWAVE_PLUS_INFO 1
CONFIGURATION 1
MANUFACTURER_SPECIFIC 1
POWERLEVEL 1
PROTECTION 2
FIRMWARE_UPDATE_MD 1
ASSOCIATION 2
VERSION 2
SECURITY 1

Reference Documents

LZW30 Manual LZW30-Manual.pdf
LZW30 image LZW30-1-570x570.jpg

First added to database on -0001-11-30 00:00:00. Current released version is 2.
Last updated by Ben Martens on 2019-11-01 05:38:03 (3 months ago).
Approved on 2019-11-01 07:33:01, and last exported on 2019-12-25 16:59:51.

Comments  
# Ben Martens 2019-09-29 22:21
endpoint command class settings likely need further updating, as switch has S2 support.
open-Z-wave alliance data likely incorrect for parameter 1 (on-off status), which reflects dimmer switch values. The Inovelli manual for similar LZW30-SN reflects the values used here, 0-2.
# Ben Martens 2019-11-01 05:21
Due to discrepancies in documentation, this switch may possibly support notifications via the LED bar at the bottom right. I have added a parameter 8 (similar to the LZW30-SN) to potentially support this. It may need to be removed afterwards.

You have no rights to post comments