Device Overview

ManufacturerAeotec Limited
Manufacturer ID0371
NameAeotec NanoMote Quad
Device DescriptionNanoMote Quad
CategoryWall Switch
References (Type:Id)0102:0003
Firmware VersionsAll
Protocol Version4.061
Library TypeLIB_SLAVE_ENHANCED
Always ListeningNo
Frequently ListeningNo
Supports RoutingYes
Supports BeamingYes
Supports SecurityNo
Maximum Data Rate40000
Device Overview

Aeotec NanoMote Quad has been crafted to control connected lighting using Z-Wave Plus as a Z-Wave S2 device. It is powered by Aeotec’s Gen5 technology. You can find out more about NanoMote Quad by following that link.


To see whether NanoMote Quad is known to be compatible with your Z-Wave system or not, please reference our Z-Wave gateway comparison listing. The technical specifications of NanoMote Quad can be viewed at that link.

  1. Z-Wave Plus certified for good compatibility (500 serials chipset)
  2. Z-Wave S2 system
  3. Support remote control anywhere and anytime
  4. Program up to 4 customized scenes
  5. The battery is rechargeable and replacable, will run for three months per charge
  6. Support low battery alarm with buzzer
  7. Support Child Lock function
  8. Supports OTA firmware update

Note: You need to send a wakeup notification to the controller to add the device as a Thing. Follow the "Adding Your NanoMote Quad to your Network" instructions.

Inclusion Information

Adding your NanoMote Quad to your Z-Wave network.

With your  NanoMote Quad now powered, it’s time to add it to your Z-Wave network.

  1. Place your Z-Wave primary controller/gateway enter into pairing/inclusion mode. 
  2. Take your NanoMote near to your primary controller.  
  3. Double click the NanoMote button (can be any button), the LED will blink rapidly with a white color. 
  4. If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about 10 seconds, then flash green to indicate it is awake. If the adding was unsuccessful and the red LED will be solid for 2 seconds and then off, repeat the above steps.
  5. If your NanoMote does not go to sleep on its own, press and hold for 2 seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
Exclusion Information

Your NanoMote can be removed from your Z-Wave network at any time. You'll need to use your Z-Wave network's main controller/gateway. To do this, please refer to the part of their respective manuals that tell you how to remove devices from your network.

  1. Put your primary controller into device removal mode.
  2. Take your NanoMote near to your primary controller.
  3. Double click the NanoMote button (can be any button), the LED will become a solid green color.
  4. If your NanoMote has been removed from your Z-Wave  network, its LED will begin cycling through rainbow colors. 
Wakeup Information

Send a wake up notification.

In order to send your NanoMote Quad new configuration commands, OTA, or receive other commands from your Z-Wave controller or gateway, it will need to be woken up.

Enable Wakeup:

  1. Press and hold button (any button) for 5 seconds or until LED turns to a green color

    LED will change from:

    Orange
    Green //at 5 seconds.

  2. Release the button and the LED will flash green rapidly to indicate it is in an awake state.

Disable Wakeup:

  1. Press and hold button (any button) for 2 seconds or until LED turns to a orange/red color
  2. Release the button and the LED should be deactivated
Usage Information

The NanoMote Quad supports 9 association groups, all control buttons can activate the configured scenes via sending the Central Scene Notifications to primary controller/gateway (In association group 1). In order to use Association Groups, make sure that your gateway or software can allow you to set these (ie: Vera Group Association Setup), in order to do so, please refer to your gateways manual on setting group association. This will allow the NanoMote Quad to directly communicate ON/OFF or Dimming commands to your devices without going through your gateway.

Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_WALL_CONTROLLER
Specific ClassSPECIFIC_TYPE_BASIC_WALL_CONTROLLER
Unique Referencezwa003

Configuration Parameters

Parameter 32
Bitmask
LabelLevel for low battery
DescriptionSet the level for "low battery" alert
Word Size1
Default Value20
Allowable Range10 to 50
Overview
Options
Parameter 43
Bitmask
LabelLow battery buzzer
DescriptionEnable/disable low battery buzzer
Word Size1
Default Value0
Allowable Range0 to 1
Overview
Options
Option Value0
Option LabelDisable
Option Overview
Option Value1
Option LabelEnable
Option Overview

Association Groups

Group ID1
LabelLifeline
DescriptionCentral scene notification
Maximum Nodes1
ControllerYes
Overview
Group ID2
LabelButton 1 basic
DescriptionOn/off control via button 1
Maximum Nodes5
ControllerNo
Overview
Group ID3
LabelButton 1 multilevel
DescriptionDim control via button 1
Maximum Nodes5
ControllerNo
Overview
Group ID4
LabelButton 2 basic
DescriptionOn/off control via button 2
Maximum Nodes5
ControllerNo
Overview
Group ID5
LabelButton 2 multilevel
DescriptionDim control via button 2
Maximum Nodes5
ControllerNo
Overview
Group ID6
LabelButton 3 basic
DescriptionOn/off control via button 3
Maximum Nodes5
ControllerNo
Overview
Group ID7
LabelButton 3 multilevel
DescriptionDim control via button 3
Maximum Nodes5
ControllerNo
Overview
Group ID8
LabelButton 4 basic
DescriptionOn/off control via button 4
Maximum Nodes5
ControllerNo
Overview
Group ID9
LabelButton 4 multilevel
DescriptionDim control via button 4
Maximum Nodes5
ControllerNo
Overview

Endpoints

Endpoint NameEndpoint 0
Endpoint Number0
Basic ClassBASIC_TYPE_ROUTING_SLAVE
Generic ClassGENERIC_TYPE_WALL_CONTROLLER
Specific ClassSPECIFIC_TYPE_BASIC_WALL_CONTROLLER
Command Classes
Class Ver Basic NIF Sec UnSec
NO_OPERATION 1
BASIC 1
SWITCH_MULTILEVEL 2
Dimmer
ASSOCIATION_GROUP_INFO 1
DEVICE_RESET_LOCALLY 1
CENTRAL_SCENE 3
Scene Number
ZWAVE_PLUS_INFO 1
CONFIGURATION 1
MANUFACTURER_SPECIFIC 1
POWERLEVEL 1
FIRMWARE_UPDATE_MD 1
BATTERY 1
WAKE_UP 2
ASSOCIATION 2
VERSION 2
SECURITY 1

Reference Documents

NanoMote Quad Manual NanoMote-Quad-user-guide----Aeotec.pdf
Aeotec NanoMote Quad image Aeotec-NanoMote-Quad.jpg

First added to database on -0001-11-30 00:00:00. Current released version is 4.
Last updated by Jeff Bailey on 2019-04-27 18:10:11 (5 months ago).
Approved on 2019-04-28 12:37:47, and last exported on 2019-04-28 12:37:49.

Comments  
# Lorenzo Thurman 2019-02-10 17:43
Not sure how to handle the errors
Reply | Reply with quote | Quote
# Lorenzo Thurman 2019-02-14 02:19
Updated category. Added product manual.
Reply | Reply with quote | Quote
# Lorenzo Thurman 2019-02-25 23:28
Added more info and product image.
Reply | Reply with quote | Quote
# Lorenzo Thurman 2019-04-01 01:53
Clarified which instructions to use when waking the device to add as a "Thing"
Reply | Reply with quote | Quote
Add comment